Jump to content
SAU Community

Recommended Posts

Hello guys,

Still wrecking white R32 GTR, have sold most bits but have still got a lot of small stuff left. Will put engine parts on the bottom of the list.

12 coil packs, 6 of them were from the white gtr, ran fine but was only running std boost. 6 are from my grey gtr, worked well but started breaking down over 20 psi. $50 for the whole lot

Steering rack with tie rod ends, $50

Clutch slave cylinder $20

Clutch master cylinder $30

Brake Booster $30

Power steering resevoir $10

AC condensor, radiator sorta thing $30

Factory rubber intercoller hoses x 3 $60

AC fan $20

Front wheel speed sensors $50

Front right hand hub with driveshaft, front left hand hub with upper and lower arms and driveshaft $100 pair

Passenger seat, just been professionally cleaned $150

LH door, white, missing the latch and central locking piece, paint bit rough but door good $100

Bare steering column $20

Taillights, no surrounds $30 pair

Drivers side headlight, has had hole cut in bottom of headlight, dont know why but it doesnt seem to affect its operation. Could plastic weld a piece in there if you wanted it to look mickey mouse, even though you cannot see it once it is mounted in car $30

Starter motor $30

Rear cradle with brakes, diff and suspension arms, missing hicas and the hicas arms $500

Front crossmember $80

Gearbox, has done 500km on a full $1500 rebuild, the transfer case had done 2000km on a full $1000 rebuild. Only used synthetic gear oil. pretty much brand new $1500

Pair of HKS 2530's, pretty much brand new,were fully rebuilt after i blew engine, cost $2500 to repair the pair of them. Once rebuilt i put them on another engine and the other engine and i couldnt get other engine to run right so i removed them again. Selling for cost of rebuild $2500

Reco head, head has the same story as the turbos, blew engine, got new head built, Has $1400 worth of stainless steel valves in it, type B cams, heavier valve springs, all reshimmed etc by engine reconditioner. Sell for $2200

Sump with diff etc, diff good but needs checking, i havent had in a car for a long time. $50

Gmax 6 spoke white wheels, 17x8 with +32 offset, no tires $400

Have got heaps of other little engine and car parts, just ask.

Thanks,

Michael

Link to comment
https://www.sau.com.au/forums/topic/298184-for-sale-wrecking-r32-gtr/
Share on other sites

Hi Michael, I do still want the coil packs and sump and diff, plus Front right hand hub with driveshaft, front left hand hub with upper and lower arms and driveshaft , and need to catch up witjh you and have a chat, cheers Damo

Edited by madaz R33
Hi Michael, I do still want the coil packs and sump and diff, plus Front right hand hub with driveshaft, front left hand hub with upper and lower arms and driveshaft , and need to catch up witjh you and have a chat, cheers Damo

Hmmm, i have had the coil packs and the sump in my boot of the statesman for about 3 months now. Have tried to call you and have sent you text messages and havent had any answer back. So i presumed you didnt want them anymore.

Also,

Why do you need the hubs with driveshafts? There was nothing wrong with the ones i sold you on the car unless you bent the ones on your white GTR?

Coil packs are pretty much sold, you can still have the sump and diff and some1 is after the driveshafts and hubs.

You better call me

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
×
×
  • Create New...