Jump to content
SAU Community

Recommended Posts

I was at Chaddy about an hour ago and noticed a few guys walking around the carpark in what appeared to be police unifroms and fluro yellow vests. On closer inspection, they were Sheriffs.

Then I saw a white Camry with UHF antennae on the boot followed by 2 identical cars. The lead car had a camera mounted above the rear door. Had a chat to one of them and it turns out they drive through the carparks slowly and the camera reads number plates, flagging anyone with outstanding fines. They found one next to my car and clamped it. They put massive stickers on the cars windows.

On the other side of the carpark was what looked like a booze bus. They must have been 20 of these white Camrys parked around it.

I guess it's not suprising considering the millions of dollars of outstanding fines. Shopping centres hold a high density of cars and the owners aren't around whilst the clamps are atttached.

Not a bad idea, coz suddenly the tables are turned and now the wanted have to chase up the Sheriffs.

post-18271-1259743470_thumb.jpg

post-18271-1259743508_thumb.jpg

post-18271-1259743534_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/298699-sherrifs-dept-blitz-today-chaddy/
Share on other sites

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

http://online.fines.vic.gov.au/fines/Conte...=1&l=107-50

"It is a serious offence to tamper with or remove a wheel clamp that has been fitted to a vehicle. The maximum penalty for a first offence is in excess of $6,805* or six months imprisonment."

Also read somewhere a while back that Sheriffs have been advised to take pictures of the cars location when they've put the wheel clamp on to avoid people removing them and denying that the clamp was ever fitted.

Just spoke to a mate who is part of the operation at the moment. He drives one of those camry's daily but it doesnt have the camera in it.

But they all carry wheel locks. I must say though some of the stories he has told me and the scum he deals with I don't blame them for doing things like this.

He has this huge folder of names, listed in priority and he just works through them...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...