Jump to content
SAU Community

Oil Leak From Near Cylender Head

koduRB25det

By koduRB25det,
in General Maintenance

 Share

Recommended Posts

koduRB25det Community Regular

koduRB25det

Posted
Posted

Got a small oil leak in my r33 gtst from past 2 weeks. It is starting from between head and engine block near gear box. It is not dripping oil but gradually it increase. I just wonder is it my head gasket….? I have no coolant leak of smoke on my car. Any way to fix this thing without replacing head gasket…?Pls help

Link to comment
https://www.sau.com.au/forums/topic/298950-oil-leak-from-near-cylender-head/
Share on other sites
koduRB25det Community Regular

koduRB25det

Posted
  • Author
Posted

no i chked that its not the half moon seal mate.

i cleaned the thing and chked. its starting from last head bolt towards to gear box. i did the compression test. they all ok. results are 165:170:175:165:174

Sure its not your 1/2 moons leaking?
shyr33 Community Regular

shyr33

Posted
Posted

As 'payback21' said, I thought I had a similar problem then I looked at the back of the engine and found oil slowly leaking from the rocker cover gaskets down near the gearbox area. So have a look at that. It's alot cheaper and easier to replace than a head gasket!

mad082 Grand Master

mad082

Posted
Posted

i wouldn't be suprised if it was just the usual rocker cover leak. this is extremely common.

if it is actually coming from between the head and the block then a compression test wouldn't show much as that only shows what is happening between the head and the block around the piston. the block could have a hole in the side of it and you could still get a decent compression test reading.

koduRB25det Community Regular

koduRB25det

Posted
  • Author
Posted

this is the oil leak from. pls see the image

I can see oil on that bolt b4 it driping to the bell housing.slowly oil leak spreading back of the engine.

what do u think abt this.

I did my compression test again using different gauge. [T&E Compression Tester]

results are

110:110:120:110:120:120

my prob is car is running very smooth. no smoke nothing. and it hits 10 psi 3000-3500 rpm when the engine is warm up.

im using castrol edge 10w-60. car want rev up to red lne. but b4 i use 0w-40 castrol edge. those days it rev up to 6000 rpm no prob.

pls consider these things and write ur sugession. im not very good with rb engines

i wouldn't be suprised if it was just the usual rocker cover leak. this is extremely common.

if it is actually coming from between the head and the block then a compression test wouldn't show much as that only shows what is happening between the head and the block around the piston. the block could have a hole in the side of it and you could still get a decent compression test reading.

post-68136-1260436475_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • bcozican
      WTAC 2025

      By bcozican · Posted

      i will be there 😁
    • patrickxdf12
      Squeaking clutch/throw out bearing

      By patrickxdf12 · Posted

      Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...