Jump to content
SAU Community

Recommended Posts

Depends where you garage and use your car. If it sits out in the sun a lot during the year like mine then I would suggest that it will need polishing up to 4 times per year. ( I live in Brisbane and lots of uv degradation of paint) but if kept inside mostly and you live well south of the tropics then you might get away with less frequent polishing. Though black is one of the hardest coloured cars to maintain.

Lots of good polishes on the market. I personally prefer Mcguiars NXT generation Tech wax 2. Good prep is most important so get it buffed first or at least buy a quick clay cleaner (I use the Armourall one because its cheaper and just as good as the Mcguiars). Wash it weekly if you can and run your hand over the paint surface after wash and chamois dry. If you no longer feel the smooth slippery suface that it had after polishing then you need to repolish. And if it has been more than a few months then a quick clay treatment will remove a lot of surface contaminants without having to go to the trouble of re buffing.

Good luck

Washed weekly, or 2nd week if i don't drive it much (it's a weekender).

Most washes will be followed up by a spray wax afterwards.

Waxed approximately once every 3 months, as it's a weekender that doesn't see much sun/use.

Proper clay, machine cut/buff, polish, liquid sealant, paste wax once a year.

I use mostly Pinnacle products. My wash liquid however is megs nxt.

Sometimes the bonnet, roof and boot will get waxed for the heck of it (these are your most hard hit areas from UV). Almost all old cars will suffer paint fade/crack on bonnet first, followed by roof and boot at the same time.

Hrmm, i'm due to give my V a big detail..

I'm a major fan of Meguiars' products. I go by the one rule I was given when my Maxima was resprayed over a decade ago ... polish and wax your vehicle when the water stops beading. That's typically every 6 months in my case, with 300km long trips perhaps 10 times in a year and often garaged up whether at home or at work.

When the time comes, it's a five step process:

Wash, Scratch-X for the more stubborn spots, surface prep/polish with their Gold Class Surface Prep, Show Car (#7) glaze and wax with Gold Class Wax.

Edited by The Max

Couple of options...but you have to make sure it IS only dust, not dirt etc (for the contact methods).

A good quality microfibre cloth, DO NOT apply pressure. Simply let the cloth glide over the paintwork. Applying pressure will cause the dust/fine dirt to be pushed against the clear coat, thus creating microscratches aka swirl marks (round scratches you see in the sun, but don't see when there's no strong light etc).

Couple of companies make a dusting brush..it's a large brush with many strands of a special type of fabric coated in paraffin wax amongst other stuff.. that should work ok too.

A watering can is another option.. long as your car is well waxed, pour the water over the car and as the water runs off, it will collect the dust and dirt. It takes some practice to achieve the "sheeting" effect, which is where you pour the water in a certain way so when it runs off, the paint is 90% or more dry.. leaves only a few spots of water you dab with an MF cloth. Youtube has some videos of people showing how to sheet water on paint.

Can also use a waterless wash system..these are self explanatory when you buy the kit.

How about if i just wanna get rid of dust ?

wipe it with a cloth or duster ?

Meguiars Final Inspection and a cotton cloth. Very handy for bird droppings too when they're no older than a few hours. As was said before, make sure it's only dust or light dirt and not medium-heavy dirt when using this stuff.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...