Jump to content
SAU Community

Recommended Posts

My car is at the mechanics getting a major service & an R33 SII turbo fitted. He just called to tell me there is problems with waterlines. He said i will need parts from a wrecker which is not good as most state these turbos as a 'bolt on fit'.

If anyone who has performed this swap can point out the oil or water lines that dont fit & how they got around the problem it would be greatly appreciated.

I will check it out at lunch and edit the post once i have had a good look at the problem... i really dont want to hunt around in wreckers unless absolutely necessary

Link to comment
https://www.sau.com.au/forums/topic/29922-arghh-waterlinesturbo-swap/
Share on other sites

It is a straight fit...i bolted on a r34 turbo myself (not r33) and everything was still a straight fit!

It was new so didnt come with any water/oil lines, all the original connections

bolted up, i think one of the water lines i loosened one support to allow me a bit more slack but it all lined and bolted on.

All i bought was an oil gasket for the oil drain.....

100% without a doubt its a bolt on job for the oil and water lines. The compressor outlet pipe you need the r33/r34 one though. (usually comes with turbo).

well i just got back from the mechanics & apparently some skyline turbos have different diameter banjo fittings as the ones on the new turbo dont fit through the original lines!!

new turbo is the one 45v2 on the compressor & is currently bolted onto the car but the lines will have to be fitted with the bigger banjo ends to finish the job.

lesson: check the banjo fittings before doing this swap.

yep thats the one. bloody waterlines.at least i'm not the only one i spose (means i'm not swapping to an unknown turbo).

most say that they have had no probs. it must have been for a certain year/model. maybe the early r32s like mine had the older (smaller) size banjo fittings.

looks like i'll be visiting some wreckers... :)

I've done the swap too with no probs. Mid 92 GTSt to a GCG highflow, 45v1 on the comp cover if memory serves. Not that its any help now :)

But i did do a turbo swap on my S4 rx7 and Mazda had changed the oil banjo bolt sizes mid run, the bastards.

hmmm... now the tedious task of ringing around wreckers for the pipework with larger banjo's. if its a SII problem that makes it more difficult again as wreckers are less likely to let go of small parts on newer engines

according to the boys at just jap (see the sponsor at the top) the turbos changed during the r32 not between 31 & 32!!

apparently the first if the r32's had a similar turbs to the red top rb20, this is why some people have had probs and others haven't.

lesson: early 32s = not bolt on fit

later 32s = bolt on fit

will add to this if there are any further differences (i'm really hoping not!!)

yep thats what the just jap lads said. probably why my car felt a little laggy than others i've been in. it seems the popular belief is that the bb's came in when the R32 did - not during the R32 model run.

but, as it turns out, not all R32's ran ball bearing turbos.

at least the SII turbs should be a decesnt improvement over the old one!

If you're going from a non bb turbo to a bb turbo make sure there is a restictor in the oil line or it'll blow smoke like a biatch.

The stock oil line off an rb20 with a bb turbo will have it in but a non bb wont.

I put a RB25 BB turbo on my old NICS RB20 about 5 years ago using the RB20 oil and water lines. I just bored out the banjo fittings until they fitted. I used this turbo for over a year and never had a smoke problem. I ran 13psi and found that the turbo spooled up quickly and the car produced power all the way to the red line. It was a nice improvement.

Geoff.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
×
×
  • Create New...