Jump to content
SAU Community

Recommended Posts

yer i found a leak...

The bracket for the heat sheild makes the contact between the dump and turbo realy uneaven...

I have exhaust wrap over the dump. My question is can i go without the heatsheild? does it realy block that much heat? I can just mount the wires up a bit higher near the abs, will they melt or anything?

2. Is the wire/connection that goes in the top of the dump my knock sensor?

do you know a way of mounting the heat shield without using the bracket that goes between the dump and turbo... Cuz it doesnt do up any tighter and there is still a gap cuz its uneven.. I just put it togethor then without the shield and i was just going to put exhaust wrap over the connection and wires that come from the top of the dump... But if it makes a big difference i would like to put the shield back on....I dont know how to mount it tho.... + i polished it last night :D

If I read you correctly, you've stuck the heat shield bracket BETWEEN the turbo and the dump. Right?

It goes OUTSIDE the flange ie dump mounts up to turbo, and bracket sits on dump, then put bolts thru bracket and dump into turbo.

The wire / connection is the O2 sensor.

2. Is the wire/connection that goes in the top of the dump my knock sensor?

Nope. The knock sensors are on the inlet side of the block underneath the inlet manifold.

The sensor in the top of your dump pipe is the O2 sensor...

Can't help with the mounting sorry :D

If I read you correctly, you've stuck the heat shield bracket BETWEEN the turbo and the dump. Right?

It goes OUTSIDE the flange ie dump mounts up to turbo, and bracket sits on dump, then put bolts thru bracket and dump into turbo.

The wire / connection is the O2 sensor.

GAWD IM A DUM SH1T!

haha.. i cant beleive i didnt do that..

thanks mate

in the attached image.. the green ones are the bolts that i have done up tight.. the 2 red ones i cant do up cuz there is no room to tighten them cus the spanner or whatever else i use hits the dump and cant be turned... how could i tighten these up? I cant feel any air or hear any leak from it...

ok image didnt upload... I have the four outside ones done.. The other 2 are impossible to get to.

I havent realy tested it out yet.. i have only gone to .4bar.. Should i turn boost down or anything like that first... i only have a bleed running .8 atm... this was before the pipe/cat was put on... Should i be listing to anything while i am testing it?

thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Im not entirely sure exactly what or where its leaking from, he started to pull the boots to swap to my new tie rods + ends and it just vomited fluid, so he closed em up up, swapped the rod ends to the old rods and let me know so I can figure a solution out, im guessing its all origional as as I passed 103k miles earlier this year im sure its just in need of a full overhual/rebuild anyways.    If i could just yank it off and be good it wouldn't be an issue to ship it out and wait for the turnaround but the guy I work with doesnt really have space to keep my car for a week or two at a time, would rather drop it off and have a replacement ready to drop in
    • What do you mean by "seals"? Internal hydraulic seals (ie, is it leaking PS fluid?) or the rack boots that close the rack onto the tie-rods? Because the former is a rebuild, and the latter is trivial that you or any nearby mechanic could do. Dunno about the cowl. Just buy what you think is required and get anything else you find/break afterwards. Wing? Dunno. Don't like R33s enough to pay attention to them. Mirror glass is just glass (on the surface that you want to polish). Go for it.
    • Hello! Long time lurker, been using the forums to address concerns and questions from afar for a while but I've struggled to find some answers so I guess its about time I made an account and formally asked some more knowledgeable people, since finding local skyline owners is hard (and shops that are knowledgeable or trustworthy to work on 'rare' cars are non existent out where im at, as skylines are quite uncommon to find in the wild around here). So the main 3 questions I have, 1: Steering rack has blown seals, well.. they kind of hold but they are not sealed properly anymore and as my R33 is my DD, i cant exactly rip the rack out and send it off or attempt to fix myself. As most refurb ones are around $1,100 or more shipped, and I have other things I need to work on around the car, I was seeking clarification on whether an S15 rack will more or less bolt right in, and whether a common mechanic could do any other required work to get it to fit. I ask, as I've found a supplier than can sell a manufactured as oem one for around 400, if not I'll likely order a used one from Jacks JDM, and take a risk on the seals there. The second question i have is that im replacing the front wiper cowl and have planned to buy 4 new clips and a new center clip but wasnt sure if there were any other clips that would also need to get replaced while I was at it. Given im sure any that are there now will simply break when I remove the old cowl... Last thing would be a fairly straight forward question, i think. If I manage (strong if, finding one has proven to be a pain) to find a R33 GTR spoiler/wing will it require much modification to bolt to a S2 R33 GTST? I've read the bolt patterns dont match but otherwise would bolt in, only options I have found with much luck is China stuff on ebay and carbonetics, which has a nice $650 shipping fee... so if anyone has any pointers where a US chap could locate one that would be great Random side question as well, the mirrors as I understand are mirror glass, and as im planning to polish my windows from water spots and surface scratches, i was hopeful cerium oxide would be fine for them too, as my research points to, but clarification is always nice. Any pointers would be appreciated, and while I have scoured the internet for answers if I missed a prior post somewhere that may answer these directly please point me towards it, as i must have simply missed it. I have seen a post here or there that has mentioned it, but I usually get 50-50 answers, or half answers... I dont have a lot of fab experience or mechanic experience, outside of hydraulic and pneumatic stuff I did in the military and with how hard it is to source stuff in the US, id rather not wing it and hemmoraghe money lol. Thanks guys! Sorry for the monumental first post haha
    • Yep, there's a very minor drift left that happens a few seconds after letting go of the steering wheel, but not enough to bother me. Enjoying the car still!
    • Got you mate. Check your email!
×
×
  • Create New...