Jump to content
SAU Community

R32 Gtr Turbo's, R32 Gtr Exhaust Cat Back, Stainless 3"

sebastion
 Share

Recommended Posts

sebastion Proficient

sebastion

Posted
Posted

hey guys, have a few spare parts that we need gone...

pair of r32 gtr turbo's, come with everything pictured (bar surrounding items and head)... turbo's are in average condition, some shaft play, to be expected due to their age... not sure of k's, was purchased with some other parts we needed...

$400 with the lines (as pictured) $350 without, also have a pair of O2 sensors, which we can supply for an extra $60...

R32 GTR 3" exhaust, cat back, stainless steel, in good condition, no holes etc... de-cat pipe not included... $350

r32 GTR standard front pipe, with heat sheilding etc-as pictured, in good usable condition... $60

Rb26 polished camshaft covers, highly polished, alot of money went into these, selling cheap at $650

Rb26 polished plenum, highly polished, looks great... also have ported runners internally to smooth flow... $600

located on the far north coast NSW, near lismore, can personally deliver as far up as brisbane at a cost, otherwise aus wide postage is available at buyers expense (for the smaller items). cheers

post-53835-1260696245_thumb.jpg

post-53835-1260696462_thumb.jpg

post-53835-1260696538_thumb.jpg

post-53835-1260696602_thumb.jpg

post-53835-1260696690_thumb.jpg

post-53835-1260696803_thumb.jpg

post-53835-1260696910_thumb.jpg

post-53835-1260696986_thumb.jpg

  • 2 weeks later...
sebastion Proficient

sebastion

Posted
  • Author
Posted

common people, someone must want a decent exhaust... taking reasonable offers, and we can deliver to you if you are close... need the exhaust gone, price drop on turbos to $250 firm...

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

sebastion, or should i say levi/alex

As you are a business/trader you are required to pay trader fee's to advertise your goods here.

Details can be found here:

http://www.skylinesaustralia.com/forums/Bu...se-t294953.html

Premium traders are currently full.

Also, do not troll the WTB section/send PM's to people about goods, this still counts as trading.

Thanks.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...