Jump to content
SAU Community

Just Watched Avatar 3d

Pal

By Pal,
in WA Wasteland

 Share

Recommended Posts

Pattygtst Veteran

Pattygtst

Posted
Posted

saw it last night at imax carousel. Awesome movie.

I wasnt impressed though with imax carousel was expecting a much larger screen, they gave us these bulk dirty smudged up glasses. Took me a while to get over that.

  • 2 weeks later...
Stinky Rooster Grand Master

Stinky Rooster

Posted
Posted

Does anyone know exactly how they did the animation? It seemed worlds ahead of the stuff I have seen in other movies.

IMO its gonna clean up come awards time, the movie was very well made, but am I alone in thinking it was a bit too much like the story of Chaka Zulu (albeit, with a happier ending)?

Scottydoo Community Regular

Scottydoo

Posted
Posted
Does anyone know exactly how they did the animation? It seemed worlds ahead of the stuff I have seen in other movies.

IMO its gonna clean up come awards time, the movie was very well made, but am I alone in thinking it was a bit too much like the story of Chaka Zulu (albeit, with a happier ending)?

I found this pretty amusing

post-44229-1264409401_thumb.jpg

lol

I did like the movie though, cool effects

  • 3 weeks later...
Crackfox Community Regular

Crackfox

Posted
Posted (edited)

:P

The glasses pissed me off and it felt like I was crosseyed for half the film. It pissed me off so much i ended up watching the last half without the glasses on so it was blurry but my eyes didnt burn. Hope this doesnt mean I wont be able to watch 3d shit in the future

Storyline was very unoriginal as well felt like a repeat of dances with wolves, pocahontas and probably 5 other hollywood films

also had to sit away from my friends cos it was full so we got split up. I sat next to some fattie that farted twice

Edited by Crackfox
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...