Jump to content
SAU Community

Recommended Posts

  • Replies 169
  • Created
  • Last Reply

Top Posters In This Topic

once again it was good to catch up.... i know ive been slack in the meeting up department :/

good to see some new faces. have a good new year an ill see you in twenty ten

from the guy '' how did he fit those rims under thos guards '' S14

BOOM!!!

Hey guys, haven't had the chance to post till now.. Awesome cruise, lookin forward to more in the future. And I don't know if u guys realized but I had to leave without saying goodbye cuz I had an urgent call from the misses on the way to chinabar and had to take a left turn on to the freeway. Anyway it was nice meetn u all. C youz next time!

Heh i just drove down there to check

Open untill

5:30 Mon, Tues, Wed Fri?

9:00 Thurs

6:30 Sat ?

Closed Sunday

Monday 9am til 8.30

Tuesday 9am til 8.30pm

wednesday 9am til 8.30pm

thursday 9am til 9pm

friday 9am til 10pm

saturday 9am til 10pm

sunday close

thats the cafe's hours.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...