Jump to content
SAU Community

Codes For The Active Lsd Computer

guru_ray
 Share

Recommended Posts

guru_ray Rookie

guru_ray

Posted
Posted (edited)

Hi all,

I have looked far and wide but i still can't find what I am looking for.

Does anyone have a list of the codes that the control module for the A-LSD flashes out when an error is detected?.

On the underside of the module in the boot is a light that flashes codes in the same way that the ECU does.

Edit 'my car is a 1993 r33 GTS-T manuel.

Thanks

Ray.

Edited by guru_ray
Link to comment
https://www.sau.com.au/forums/topic/302002-codes-for-the-active-lsd-computer/
Share on other sites
guru_ray Rookie

guru_ray

Posted
  • Author
Posted

OK,

This seems to be a hard question.

If someone out there wants to do me a favour?

Moanie suggested in one of her posts she knew what one of the the codes was on her A-lsd module.

If somebody wants to send a PM to Moanie ask if she can post the codes here, if she has them.

Moanie if you don't have codes for the A-Lsd module where did 'read' the TPS error?

I cannot send personal messages until i have made 10 posts.

I don't see the point in spamming threads just so I can send a message.

If the answer is out there lets get it up here! :bunny:

Ray

ps. if you send a message to Moanie post you have done so, so she don't get a mailbox full of spam.

Deano45 Rising Star

Deano45

Posted
Posted
OK,

This seems to be a hard question.

If someone out there wants to do me a favour?

Moanie suggested in one of her posts she knew what one of the the codes was on her A-lsd module.

If somebody wants to send a PM to Moanie ask if she can post the codes here, if she has them.

Moanie if you don't have codes for the A-Lsd module where did 'read' the TPS error?

I cannot send personal messages until i have made 10 posts.

I don't see the point in spamming threads just so I can send a message.

If the answer is out there lets get it up here! :bunny:

Ray

ps. if you send a message to Moanie post you have done so, so she don't get a mailbox full of spam.

I don't know if you have seen This but it has links to other topics on the SAU forums that have lot of info on the Active LSD option in R33 skylines. Maybe try checking it out first. It may clear your error for you but doing some simple bleeding.

guru_ray Rookie

guru_ray

Posted
  • Author
Posted

Deano45

Dead link for me?.

I have studied all the links in the sticky at the top of this section of the forums if that was what you were referring to.

I am trying to read the codes so I can get this thing working properly, I am single spinning at the moment.

And have two codes one is TPS the other I don't know.

Thanks all help appreciated.

Ray.

guru_ray Rookie

guru_ray

Posted
  • Author
Posted

Stock ECU is in the car now.

Codes I have are 75 which i believe to TPS

And 62 which if the same as the Attessa codes would be front and rear right G sensor???? I don't think the GTS-T has G sensors???

Will be going with apexi powerfc later and splicing the wires for the TPS, If I get the A-LSD working that is.

Ray.

Deano45 Rising Star

Deano45

Posted
Posted
Deano45

Dead link for me?.

I have studied all the links in the sticky at the top of this section of the forums if that was what you were referring to.

I am trying to read the codes so I can get this thing working properly, I am single spinning at the moment.

And have two codes one is TPS the other I don't know.

Thanks all help appreciated.

Ray.

Sorry try this link

The other link didn't post properly

What error codes are you getting?

PM-R33 Grand Master

PM-R33

Posted
Posted

The G-sensors it is referring to is the wheel speed sensors. This is what your ABS uses also, hence if you have an ABS fault, your A-LSD goes to shit. This becomes a problem when doing stand still burnouts and locking up the front wheels. The ABS sometimes gets a fault since the front wheels aren't spinning but the rears are and then the diff goes into single spinner mode. Hence not the best diff if you like doing stand stills.

FineLine Grand Master

FineLine

Posted
Posted
The G-sensors it is referring to is the wheel speed sensors. This is what your ABS uses also, hence if you have an ABS fault, your A-LSD goes to shit. This becomes a problem when doing stand still burnouts and locking up the front wheels. The ABS sometimes gets a fault since the front wheels aren't spinning but the rears are and then the diff goes into single spinner mode. Hence not the best diff if you like doing stand stills.

And another piece to the puzzle fits in,

Always wondered why the car defaulted to single pegger when I did a brake lock burnout. Thanks mate.

Deano45 Rising Star

Deano45

Posted
Posted
Thanks I have read every thing there all the links.

Codes are 75 and 62.

Cheers

Ray.

I could be going down the wrong path but these are the codes for the Attesa ETS ECU in the R33 GTR.

The diff is the same one as the V-Spec, so I would assume that it would use the same/similar computer to control the diff & ABS.

Going off these codes 75 is the Throttle Position sensor. This normally looks for 0.5v fully closed. You can check this with a multimeter and move the sensor until it has that reading.

PM-R33 looks like he has covered the error 62

Error Codes:

1,5 Front right wheel sensor and circuit

2,6 Front left wheel sensor and circuit

3,7 Rear right wheel sensor and circuit

4,8 Rear left whel sensor and circuit

11,21 Front right inlet solenoid valve and circuit

12,22 Front left inlet solenoid valve and circuit

13,23 Rear inlet solenoid valve and circuit

15,25 Front right outlet solenoid valve and circuit

16,26 Front left outlet solenoid valve and circuit

17,27 Rear outlet solenoid valve and circuit

31,32,33 E-TS solenoid and circuit

34,35,36 E-TS fail safe solenoid and circuit

41,42 ABS actuator relay and circuit

43,44 ABS actuator motor , motor relay and circuit

45,46,77 ET-S/ABS control unit ground and circuit

47,48 E-TS/ABS control unit power supply and circuit

51,52 E-TS actuator motor and circuit

53,54 Pressure switch and circuit

55 Air bleed switch and circuit

56 E-TS oil level switch and circuit

61 FR and RR G sensor 1 and circuit

62 FR and RR G sensor 2 and circuit

63 FR and RR G sensor 1 or 2 and circuit

64 G sensor 1 power supply and circuit

65 G- sensor 2 power supply and circuit

66 Side G sensor and circuit

75 Throttle position sensor and circuit and sensor

PM-R33 Grand Master

PM-R33

Posted
Posted

Haha yeah, it is the most over complicated diff in history. I think one day im just gonna get rid of it and put a 1.5 way into it, it's such an annoying diff. Great when it works normally, but a pain in the ass when it decides not to work.

guru_ray Rookie

guru_ray

Posted
  • Author
Posted
The G-sensors it is referring to is the wheel speed sensors. This is what your ABS uses also, hence if you have an ABS fault, your A-LSD goes to shit. This becomes a problem when doing stand still burnouts and locking up the front wheels. The ABS sometimes gets a fault since the front wheels aren't spinning but the rears are and then the diff goes into single spinner mode. Hence not the best diff if you like doing stand stills.

Ok wheel speed sensors, where the hell are they?.

I would have thought that they would be on the hubs, with a magnetic reader and a magnet spinning with the hub?

No wiring going to the hubs at all.

There are two sensors of some sort on the back of the diff itself ether side with two wires each. I followed these wires and they go to the Hicas Module.

Stupid diff.

On a side note I have a hicas lock bar. The wiring for the hicas does no need to plugged in to make this diff work does it?

Ray

bigmikespec Veteran

bigmikespec

Posted
Posted
Ok wheel speed sensors, where the hell are they?.

I would have thought that they would be on the hubs, with a magnetic reader and a magnet spinning with the hub?

No wiring going to the hubs at all.

There are two sensors of some sort on the back of the diff itself ether side with two wires each. I followed these wires and they go to the Hicas Module.

Stupid diff.

On a side note I have a hicas lock bar. The wiring for the hicas does no need to plugged in to make this diff work does it?

Ray

There are two sensors of some sort on the back of the diff itself ether side with two wires each. I followed these wires and they go to the Hicas Module.

Well done chief, that are they!

guru_ray Rookie

guru_ray

Posted
  • Author
Posted
There are two sensors of some sort on the back of the diff itself ether side with two wires each. I followed these wires and they go to the Hicas Module.

Well done chief, that are they!

Any ideas on how test these for correct operation, is there a resistance test?.

Ray.

bigmikespec Veteran

bigmikespec

Posted
Posted
Nope HICAS does not effect the operation at all. Honestly i have never looked for the wheel speed sensors so am not sure.

They are definitely the sensors but I do not know where they go, can let you know tomorrow. But I suspect it may be of no use to you as I have a GTR.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ozdavroz
      Starting again

      By Ozdavroz · Posted

      Had another look at the car and I noticed the fuel pump isn't priming on ignition. I'd taken out the pump from the boot to siphon out the old fuel, so maybe I've knocked something loose or broken a wire putting things back together. Will go back with a multimeter and try to work out what's stuffed. Kinda hoping it's the pump itself thats gone so I can upgrade it
    • Duncan
      New R32 owner soon

      By Duncan · Posted

      Yeah agreed, you can't assume that shop are they only people who ever had to work on it. It was just a guess on the mods based on how things were done back then. You can check the Air Flow Meters by the part number on their tags, they are likely either Z32 or Nismo ones (both read about the same but the Z32 one is a little larger while nismo is stock size but supports the higher airflow like a Z32). And yes, all that would get you to 450hp / 340kw To tell what is happening with the turbos, you want a photo of the tag on the core, that will say what it was made out of  (they can retain the front and rear covers to make the plumbing easier)  
    • bardabe
      1992 R32 GT-R Race Car

      By bardabe · Posted

      I'm selling my personal race car. 1992 BNR32 Skyline GT-R About eight years ago the engine developed the dreaded low oil pressure problem. I removed it and found the issue. However shortly after I moved half way across the country, moved my work shop, bought a house, got married, then moved my shop again to it's permanent location for the time being. in turn I do not have the time to race this car as it should be. In turn the engine I built for this car will end up in my street car and this car I hope finds a home with someone who can use it to it's full potential. The roll bar was built by Jason Noren Fabricaiton in Pomona California to SCCA and NASA Specs. The car used to compete in redline time attack and global time attack enthusiast class. It also has a fire suppression system.  The car is with me at my workshop in Kyle Texas, USA. Shipping it is no problem, I can personally deliver the car to the port of either Houston or Los Angeles. Any other port depending on where it is may require transport but we can always work that out.   The chassis itself is rust free, rear quarters and under fenders are free of any rust so it's a very solid foundation for anyone who wishes to move forward with it. As posted and at the asking price of $20,000 USD the car includes all of the following;   All OEM Body panels, front fenders, rear bumpers etc.  OEM Nissan Projector headlamps (Pictured N1 lamps were removed) OEM Nismo Side Skirts / Extensions OEM Rear Spats  Front & Rear Subframes are installed car is full roller Rear Subframe has Cusco Camber Arms, Whiteline HICAS Elimination Front Subframe has Whiteline tension rods and whiteline Sway bars w/ endlinks.  Buddy Club N1 Coilovers All chassis wiring and engine wiring is in tact. Attessa System is fully in tact and was functional before engine removal.  BCNR33 GT-R Brembo Brakes F+R with Endless MX72 Plus Pads, DBA Rotors & Stainless Steel Brake lines Billion Racing Radiator Billion Radiator Hoses Fluidyne Engine Oil Cooler Accusump System (trunk Mounted) 5 Speed Transmission w/ Transfer Case F+R Prop-shafts Rear Differential With rear Axles.  Nismo Gauge Cluster Nismo Clutch + Flywheel   Essentially what is needed to make this car running and driving again is as follows: A working Engine, an ECU, and time to put it together. The price posted is or best offer as I am willing to remove some components to accommodate price to a certain extent. If any serious buyer wants full detailed pictures, videos, or any questions I'll be happy to answer them. I believe this car is priced to move quickly considering it's a rust free and very straight chassis but always open to fair negotiation.  I can be contacted via phone or email. (+19517081648) email is juan@bardabe.com   
    • Kapr
      Oil pan for RB25DET NEO Stagea "version"

      By Kapr · Posted

      So...to my (and my mechanics doing the swap) surprise...the oil pan from NEO engine does not fit 100% and needs to by modified like this: It is not a huge problem but in the future i want a "proper" oil pan. So question is...what different oil pan can i get to fit without any problems and modification? Thanks! 
    • Rezz
      New R32 owner soon

      By Rezz · Posted

      Some more info I found.  These are the last entries Yoshikiyo Fujii made on his blog before he passed away in 2009: http://blog.livedoor.jp/fujii_dynamics/ And finally this is where the workshop was situated:  https://maps.app.goo.gl/HhTPtHzt3WVcBTiEA  
×
×
  • Create New...