Jump to content
SAU Community

Recommended Posts

Black 1999 R34 GTR, non v spec, 66,000kms, first owner in Oz (2 years).

Price is $45,000

Nismo LMGT4 18" rims

HKS catback exhaust

Car still has original cassete deck

Flare

180kph speed restrictor

Air filter box

Car made 211rwkw on Racepace dyno before the catback, 100% stock, including exhaust and air filter box, I have the dyno sheet. Makes more now.

The only blemish on the entire car is the top of the rear spoiler could do with a touch up, slight peel. Rest of the car, inside and out is immaculate.

I will take a cheaper car as a trade, as we still need a second car. Let me know what youve got.

Car is located in Vic, has 4 months rego

Email [email protected] or ring 0404 453 542

Cheers

Markos

post-48974-1262442440_thumb.jpg

post-48974-1262442473_thumb.jpg

post-48974-1262442526_thumb.jpg

post-48974-1262442574_thumb.jpg

post-48974-1262442610_thumb.jpg

post-48974-1262442818_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/302243-r34-gtr-for-sale/
Share on other sites

I know its probably not the car your after but Im selling my Single Turbo Supra http://www.skylinesaustralia.com/forums/Si...en-t302177.html

Will happily fill an additional $7000 + that car, I know its a low ball abit but im selling my car based on its mods even though it has well over $50,000 spent on it. So it's worth alot more than im selling it for im just not after waiting 12 months to sell it for $38K

James, your car is what I'm looking for, a cheaper performance car.

In this market you will be lucky to get the $28,000 your looking for, nobody will pay for your mods, which is why I havent modified the 34.

Your dollar offer is miles away from what I expect in a trade unfortunately, not even half way sorry.

Yep, to a friend, I even took his R32 GTR as a trade in.

He lost his job and subsequently was struggling to pay the balance. Eight weeks later I bailed him out and just took my car back and gave him back his deposit, thats what friends do.

He's still trying to raise the funds, but I'm going to advertise anyway.

That's the reason the km's went from 63,000 to 66,000 lol I dont drive much anymore, he does

Thank you very much for the offers everyone, I've replied to every pm

Can I please ask that you dont bother haggling with me if you have no money, it serves no purpose

To speed the process up, rather than asking me about a swap then waiting for a reply, where I ask for details and pics, simply send me an email with pics and details straight off

[email protected]

Okay, I've got 2 serious offers and the others are tyre kickers who havent got back to me with pics or a $$$$$ ammount.

I'll wait till Monday night then I'll deal with the 2 serious guys

Unbelievably, only one guy has ever been to look at the car, and he bought it, then found he couldnt afford it.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...