Jump to content
SAU Community

Recommended Posts

Just bought this R-34 GT-T (98) 2.5 L 2 door recently, it seems to overheat only on 35degree days or higher especially when running the a/c. Makes no difference if im in traffic or crusing down the motorway, i make sure coolant is there, any suggestions or help with this ?

Link to comment
https://www.sau.com.au/forums/topic/302388-gt-t-overheating-assistance-plz/
Share on other sites

with these thing hard to say i would be getting the cooling system pressure tested, also think about basic things like replace the thermostat, radiator cap, coolant and maybe get the radiator cleaned out professionally in case its blocked.... if non of that helps maybe its got a blown hg slowly on its way.... you would hope not thou.....

Edited by rgr34
with these thing hard to say i would be getting the cooling system pressure tested, also think about basic things like replace the thermostat, radiator cap, coolant and maybe get the radiator cleaned out professionally in case its blocked.... if non of that helps maybe its got a blown hg slowly on its way.... you would hope not thou.....

cheers. i did get the first things done already, maybe now ill get the radiator/head gasket checked out professionaly.

Which is a good mechanic to take skylines for servicing with decent price?

Same thing just happened to me. Only just made it home so I was lucky in that regard. Smoke was coming out of the radiator hose and somewhere from the back of the engine to, couldn't see where it was definitely coming though.

Radiator hose was loose so I'll tighten that up and top up water & coolant levels once the engine has cooled down...and if it still overheats then I'll be coming back to this thread needing help haha

My clutch is pretty f***ed at the moment, although I didn't think that would be a cause to the car overheating?

So I put the radiator hose back in place and topped up the radiator with water. Yet it still overheats, this time its spitting and steaming from the top radiator hose (radiator end) and also, when I hit boost, the car basically starts shaking. Whats up with that?

My clutch is pretty f***ed at the moment, although I didn't think that would be a cause to the car overheating?

So I put the radiator hose back in place and topped up the radiator with water. Yet it still overheats, this time its spitting and steaming from the top radiator hose (radiator end) and also, when I hit boost, the car basically starts shaking. Whats up with that?

I mean the fan clutch.

there ae plenty of things to check before looking at headgasket, etc when it comes to heating issues.

first is to bleed the system. this is free and a good place to start. also check the clutch fan while you are at it as it's something you can check yourself. also check for any crap between the radiator and the aircon dryer/radiator. this can sometimes get a bit blocked up and educe airflow if the car is often parked unde a tree and leaves fall onto the front bar and get sucked through the grill when the car is started.

next is to replace the thermostat as this is something that does need to be replaced over time and would probably be the cause of a lot of heating issues. replace the coolant while you are at it.

then you could get the radiator professionally cleaned. in my opinion radiator flushes don't do crap as they don't get out the build up of crap that blocks the radiator core.

next on the list is the water pump. if the impellor in this is worn it won't pump the water fast enough and cause heating issues (anyone that has ever owned an outboard will know all about impellors and water pumps)

unless there is a reason to check the headgasket (such as oil and water mixing together) or bubles in the radiator when the car is running or the car is hard to start then when it does start blows a heap of white smoke for a short amount of time i don't usually bother. and milky oil or coolant isn't always the sign of a blown headgasket. i've had 2 blow and not ended up with the milk of death, but instead ended up with coolant in the cylinders.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To expand on this to help understanding... The bigger/longer the block is, the more it's going to work to sit on your far away high areas, and not touch the low stuff in the middle. When you throw the guide coat, and give it a quick go with a big block, guide coat will disappear in the high spots. If those high spots are in the correct position where the panel should be, stop sanding, and fill the low spots. However, using a small block, you "fall off" one of the high spots, and now your sanding the "side of the hill". Your little block would have been great for the stone chips, where you only use a very small amount of filler, so you're sanding and area let's say the size of a 5/10cent piece, with something that is 75*150. For the big panel, go bigger!   And now I'll go back to my "body work sucks, it takes too much patience, and I don't have it" PS, I thought your picture with coloured circles was an ultra sound... That's after my brain thought you were trying to make a dick and balls drawing...
    • Oh I probably didn't speak enough about the small sanding block for blocking large areas.  In the video about 3 minutes in, he talks about creating valleys in the panel. This is the issue with using a small sanding block for a large area, it's way too easy to create the valleys he is talking about. With a large block its much easier to create a nice flat surface.  Hard to explain but in practice you'll notice the difference straight away using the large block. 
    • Yep I guessed as much. You'll find life much easier with a large block something like this -  https://wholesalepaint.com.au/products/dura-block-long-hook-loop-sanding-block-100-eva-rubber-af4437 This is a good demo video of something like this in use -    You have turned your small rock chip holes into large low spots. You'll need to fill and block these low spots.  It's always a little hard not seeing it in person, but yes I would go ahead and lay filler over the whole area. Have a good look at the video I linked, it's a very good example of all the things you're doing. They went to bare metal, they are using guide coat, they are doing a skim coat with the filler and blocking it back. If what you're doing doesn't look like what they are doing, that's a big hint for you  
    • The odometer does go up when driving.  Does this tell it is an issue with the speedometer itself?    Where can I look for replacement cluster? Or speedo? I can likely do the repair.. Will ER34 cluster work on HR34? Or do I need a HR34 20GT S2 specifically lol   
    • Mine's a bit bigger at 70x150mm roughly. The spots are flat, just can feel the edges if I dig my nail into it. I did fix some other other ones by both using my finger to sand that small spot (I'm a bit wary of doing this and creating hot spots and a bigger mess) and I also did sand over it flat and others, but this also worried me a bit because if I create an overall low spot on the panel on paint that is good.  Correct me if I'm wrong but as long as it's flat even if I can feel the edges, I can put filler because it will all be level once I sand it? I can see myself going in a circle after sanding guidecoat with 320 grit if for example the panel is flat with my hand but because I sanded the guidecoat I could have created a low spot again somewhere. Unless where I'm going wrong is what I mentioned previously where I didn't go low enough on the grits. It's 1 step forward and 2 step backwards here haha. I'll probably need to experiment with it more. Last time I go back to bare metal lol.
×
×
  • Create New...