Jump to content
SAU Community

Recommended Posts

Hey peeps! Just installing a Turbosmart dual stage boost controller for my R32GTST properly this time. lol

I had installed it a few months ago without the wiring hooked up (so basically it was only single stage) now ive put a switch in and connected it properly so solenoid works (now working as dual stage)

My question is about the PRESSURE SOURCE PORT, on the instructions it says the pressure source port should be located before the throttle body whereas when i bought the car a year ago the pressure source was from the manifold. Here are TURBOSMARTS instructions

I do have the option of running the pressure source just after the turbo but its blocked off.

The car does have a problem with boost spiking and im wondering if the location of the pressure source port could be the issue.

my car is running 1 bar atm but boost spikes past 1 bar then settles in second gear at WOT 3rd gear just cant get to 1 bar but maybe 0.8 bar.

car has HKS2530 with front mount and turbo back 3inch exhaust with 3 inch cat so flow shouldnt be a problem right?

Any help would be appreciated :blink:

Link to comment
https://www.sau.com.au/forums/topic/302468-boost-control-question/
Share on other sites

no matter where you plug that boost controller, it will spike.. It's just a dual bleed valve. I've used one before and it's bad. Buy yourself a $25.00 Turbotech ball bearing valve and watch it hold a boost line than the Turbosmart dual stage.

Do yourself a favour and sell it on eBay and buy a mechanical valve and spend the change on grog :banana:

Ok so if i got a turbotech controller would it still matter where i hook up the source port to?

Does it make a difference if its located before or after the throttle body?

Last night i made the effort to change the lines i hooked up the pressure source to just after the turbo instead of after throttle body (manifold line) will this change get a better reading? my boost guage is also hooked up to the manifold

Cheers guys ive connected pressure source from about 1 foot off turbo but just wondering should i tee in the blow off valve vacuum into this line or just run blow off valve off plenum?

BOV needs to be off plenum, the vacuum from the plenum will pull up the piston when the throttle is closed

  • 2 weeks later...

Well went for a drive to Ballina today to look at a car show, I turned the Turbosmart dual stage low setting all the way anti-clockwise. basically it should be the stock setting. car still boosts to 1bar anyway. Does this mean I have a 1bar actutator? i also noticed with the setting as it was it would take ages to build up boost after a 2nd to 3rd change! On the high boost setting i turned it out a few clicks from fully shut, dont have slow boost problem anymore when on high boost setting.

Basically should I get rid of the dual stage? I wanted to run 10 psi on the low setting for when the gf takes the car for a drive and 1bar high, but cant get lower than 1bar

BUT i did notice when at WOT in 4th gear it would only go to 0.7bar? in second it goes to 1.1bar then back to 1bar and then stays there lol

Should i piss off the dual stage and run no boost controller or just buy the turbotech and keep the car running 1bar

its soo annoying as i dont want to spend heaps on boost control yet cause i need paint fixed then coil-overs then some nice wheels and then i might leave the car alone for a month if its lucky

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...