Jump to content
SAU Community

Internet In Narre Warren


Recommended Posts

  • Replies 88
  • Created
  • Last Reply

Top Posters In This Topic

narre warren huh? you poor poor boy..

i think you can get ADSL down there these days and i think cable too.. although seeing as every house is pretty much a housing estate, might have problems with pair gain..

netspace is one of the best ADSL providers/price/benefits i reckon. Either that or some of bigblue has some decent rates. Stay WELL WELL WELL clear of telstra. Shittest internet i ever had, email servers down, authentication problems still years after they first came on, high priced, the list goes on..

Fountain Gate, what a place :D

You can check the availability of cable for telstra and optus.

OPTUS

http://www1.optusnet.com.au/offers/cable/a...=optusnetportal

Sorry but cable is not available in that postcode area (3804).

Telstra needs an address to tell you if cable is available in the area...

However, we live in a cabled area, and can't get Optus.

:Bang:

because we got optus tv at our old house about 6 months ago with internet deal optus told me i have to pay $340 to disconnect, i told them to shove it up their ass becasue its their problem they dont provide cable in narre warren and because i have used optus cable fro around 4 years.

i will have to search around for some good broadband or asdl, and gordo i am in a housing estate and their is lots of free land with no cops around for me to test my car out

because we got optus tv at our old house about 6 months ago with internet deal optus told me i have to pay $340 to disconnect, i told them to shove it up their ass becasue its their problem they dont provide cable in narre warren and because i have used optus cable fro around 4 years.

You can try, but it won't get you very far. You'll have to keep paying each month or the cancellation fee, or eventually they send debt collectors after you. I had ADSL for 18 months - and to move cost me $100 (that wasn't the bad part) PLUS i had to be on a whole new friggin contract for 12 months. I yelled and abused them, but in the end one of the managers told me it was Telstra's fault and telstra locked them into paying some backend fee to transfer whether a new or existing user. In the end i said stuff it, and hence why i haven't been on ADSL since :D

i will have to search around for some good broadband or asdl, and gordo i am in a housing estate and their is lots of free land with no cops around for me to test my car out

Yes and no :D There are quite a few cameras in narre and cops late at night like to sit on the nice open streets and book people just 'cause - but there are some good parts. I used to go out there a bit coz a friend lived out there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...