Jump to content
SAU Community

All Japan Day World Domination Tour 2010


Recommended Posts

  • Replies 97
  • Created
  • Last Reply

Top Posters In This Topic

Haha I have the same problem!

im sure u could twist coxy's arm to drive one of yours down kristian :sick:

edit

how much detail do you want on these entrant forms? im tryin to sift my way through it (have to go get my vin off the car later on haha)

im sure u could twist coxy's arm to drive one of yours down kristian :D

edit

how much detail do you want on these entrant forms? im tryin to sift my way through it (have to go get my vin off the car later on haha)

Coxy is SUPPOSED to have entered his own damn car :(

You don't have to go too crazy on the sheet, just mods and whatever else makes it special.

whens the final day we can enter a car? and we need permission? heres a link with info about my car, im interested in entering if you let me :D

http://www.cardomain.com/ride/3835046/1

In the final days leading up to AJD, we have had an influx of entrants and its looking great!

If you can't commit to entering your car, please try to come down and support the cancer council with your donations.

^^^ Wow, that is one sweet ride! :D .... I wonder what is under the bonnet?

DSC04566.jpg

:D :D :P

Some photos of Domo's adventures :)

IMG_4189.jpg

IMG_4190.jpg

IMG_4191.jpg

IMG_4192.jpg

Free plug for the almighty AJD organiser :)

IMG_4193.jpg

IMG_4194.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...