Jump to content
SAU Community

Plazmaman

r33cruiser

By r33cruiser,
in General Automotive Discussion

 Share

Recommended Posts

Craig SLO33 Enthusiast

Craig SLO33

Posted
Posted
I ordered and paid for a plenum roughly a week and a half ago and haven't had any communication since then.

Has anyone else ordered through them?

How long did it take you go get your stuff?

Did they return your emails?

Just give them a call mate ,,easyest way and then youll know whats going on..........

Link to comment
https://www.sau.com.au/forums/topic/304406-plazmaman/#findComment-5041270
Share on other sites
W0rp3D Grand Master

W0rp3D

Posted
Posted

alot of places only just came back from the christmas break this week, if you just ordered over the internet without calling them to make sure they were open or to make sure they are in stock then thats your problem.

Link to comment
https://www.sau.com.au/forums/topic/304406-plazmaman/#findComment-5042019
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • ARB26
      GTR-Registry.com Presents: The Stagea Collection (all Stagea VIN/colours/types/options etc)

      By ARB26 · Posted

      Website is down
    • soviet_merlin
      NC MX5

      By soviet_merlin · Posted

      There are black hose clamps as well if you care. Plazmaman for example sells some: https://plazmaman.com/product/black-hose-clamps-premium-quality-stainless-breeze/
    • The Bogan
      NC MX5

      By The Bogan · Posted

      After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
×
×
  • Create New...