Jump to content
SAU Community

Recommended Posts

Bang for buck its got to be better value than an ARC airbox...

God i hope you don't believe that. That 2mm thick bit of plastic with next to zero thermal insulation that is just sitting around the pod wont do a single thing. If it drops air intake temperatures by a couple of degrees i would be impressed. Air moves believe it or not and will simply raise the temperature of that bit of plastic until it is the same temperature as the under bonnet temps. However regardless of that, the bit of plastic isn't completely blocking the engine bay heat to the pod, therefore air will simply move around it and the pod will still suck in hot air once again making that shield do nothing.

No disrespect to the OP, people giving things a go to save some money is fantastic, but to think that is actually doing anything is just silly.

Edited by PM-R33

If some one goes to the effort of doing that, taking heaps of pics, posting it up and then asking people what they think than yes i assume the guy is being serious. I have seen a lot dumber shit on these forums done by people that isn't a joke.

Edited by PM-R33

f**k you guys are funny

went on the nissan cruise yesterday, its still in there i think so it hasn't melted away

yes its prob not doing anything but hey, its was 94 CENTS, was worth a go and everyone got a laugh out of it

of course its not gonna seal up as well as something like a jjr carbon shield or an arc air box but my car came with the pod already on it and i didn't get the stock box with it either :rant: eventually i'll track one down or get a more permanent one but it was 37°c today and coolant temps were up to 90 on the fly so i can only imagine what the engine bay temps were like

i understand airflow and the concept of high and low pressures (i'm doing naval architecture at uni = hydrodynamics etc) and it probably has a bigger effect than you would think and it certainly can't have a negative effect as its surrounding 90% of the pod around the sides, it still made good power and i was keeping up with a 32 gtr and an s14 through the twistys

so in summery, yes its light hearted, no im not that serious about it but it seemed to work ok

As long as it worked, that's all that matters.

well i have no less power than b4 and i still get good fuel consumption (ecutalk display) so its not got a negative effect

well i have no less power than b4 and i still get good fuel consumption (ecutalk display) so its not got a negative effect

For all those that read other parts of SAU and dont want to bitch and carry on,

http://www.skylinesaustralia.com/forums/Ca...hl=cold+air+box

Pull the tampon out and grow a pair people.

Edited by dirtyRS4
im no techo and i am sure that he thaught it was a good cheap alternative.top points bro for having a go.

+1 from me

I feel like doing it with a MeTaL bucket, probably $4.95

:(

felt the unshielded pod before after the missus had the stag, very hot.

time for a heatshield - again.

previous unit wont fit due to my hard intake pipe setup going to the gt3076iw

so, Im going to replicate the effort and see how it feels

well for australia day i thought it would only be fitting if my turbo car was complete with flutterzzZZzzzzz

i will add this here cos i used part of my bucket waste, so this is multiple mods with one cheap bucket

basically you need to take off the stock bov which is 2 12mm bolts, 1 hose clamp (return line) and 1 hose clip (manifold signal)

then you use the gasket as an outline for a solid sheet of bucket, i.e. not leaving a hole in the centre of it

re install with the extra plasic gasket in place and your away fluttering like there is no tmrw :D

like so:

post-51118-1264404413_thumb.jpg

note: i take no responsibility for your actions and this is only for a short term period of shits and giggles

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
×
×
  • Create New...