Jump to content
SAU Community

Recommended Posts

can anyone offer advice on where i should be looking to fix up my stuffup

i decided to give my r34 gtt a wash under the engine bay, on 3 occassions i started the motor and sh ran nice.

after shamming up the excess water, i moved to the snorkal, airbox and filter.

whilst this was off i started the engine to move the car a meter or so and wammm, the air and fuel mixture is off , rough idle, and crap performance.

i tried a ecu reset and now i have the traction light / engine light permenantly on ?????????

any help is worth something

Link to comment
https://www.sau.com.au/forums/topic/305242-r34-air-box-stuff-up/
Share on other sites

Do/check all these things

make sure your air flow meter (which is a cylinder attached to the airbox and has mesh on both sides) is completely dry(let it sit in the sun for a bit?/hairdryer?), or that you haven't blown any dirt onto it's sensor as that would cause problems too...

Check that the plug/wires to it aswell to make sure they havent come loose..

Check you havent gotten some water in some cracks/all the pipes are well connected and sealed.

you said "i moved to the snorkal, airbox and filter" and then you started the car... did you have the airflow meter connected? if not, thats your issue as you car has no idea how much air it is sucking in...

also, when you did the ecu reset, was everything back in place and are you sure you did it properly? (im not sure how to do it as I have an aftermarket ecu, but just making sure)

gl with it.

Adam

hey thanks for that info,

the ecu reset was done again and this time around i got results my air flow meter sorted itself out. ( air/fuel mixtures are good )

my bad for now my TCS and SLIP light are on, wont go away. test drove her and the tractions is not working ?

is it a simply sensor or do i need to take it in to an auto electrician ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...