Jump to content
SAU Community

Recommended Posts

it would struggle to make power due to lower compression you would also need exhaust manifolds and non turbo ECU

are you already on your P's, and whats the rule going to say if you have said car registered in your name before the rule comes in

Link to comment
https://www.sau.com.au/forums/topic/307099-r32-r33/#findComment-5074383
Share on other sites

hey guys,

i was just wondering if it would be posible to take a turbo skyline (R32 or R33) and take the turbo off while on my ps because of the new p plate laws coming for south australia and put it back on after im off my ps ?? or would there be engine mods needed or wateva? Thanks.

ummm no.!

you will lose way to much power different compression ratios between turbo/non turbo models.

get a different car put the line in the shed until ur off ya P plates or just buy a non turbo car if ur that worried.

regards

Allan.M

Link to comment
https://www.sau.com.au/forums/topic/307099-r32-r33/#findComment-5074386
Share on other sites

if the law does come in, then selling a non turbo skyline down the track will be easier than selling one now without those laws :D

hahah Allan

non turbo R34 are very cheap from japan

EDIt

if your choice is only 32 or 33 get the 33 with a RB25de as the 20 would have even less guts again

R33 = RB25

R32 = RB20

GTS = DE

GTSt = DET

R33 GTS4 = RB25DE

Link to comment
https://www.sau.com.au/forums/topic/307099-r32-r33/#findComment-5074408
Share on other sites

if the law does come in, then selling a non turbo skyline down the track will be easier than selling one now without those laws :D

hahah Allan

non turbo R34 are very cheap from japan

EDIt

if your choice is only 32 or 33 get the 33 with a RB25de as the 20 would have even less guts again

R33 = RB25

R32 = RB20

GTS = DE

GTSt = DET

R33 GTS4 = RB25DE

You missed a few out

R32 - RB25DE Seen a few of these getting around

And the very rare R32 - RB26DE but I doubt you'd ever find one.

Link to comment
https://www.sau.com.au/forums/topic/307099-r32-r33/#findComment-5074446
Share on other sites

a little more info :D

didnt know you could get a CA18 in a R32, and looks like all the 25's were double cams only a couple 20 single cams

The R32 range:

GXi - The bare basic model R32 1.8 litre, rwd, non-turbo, no extras.

GTE - 2 litre family model, four door, non turbo, single overhead cam.

GTS - 2 ltr, in-line 6. DOHC, EFI, 2 & 4 drs, RWD, standard sports model.

GTS25 - 2.5ltr, in-line 6. DOHC, EFI, 2 & 4 drs, RWD, non-turbo, sports model.

GTSt - 2 ltr, in-line 6 cyl, DOHC, EFI, 2 & 4 drs, RWD, turbo charged sports car.

GTS4 - 2 ltr, in-line 6 cyl, DOHC, EFI, 2 & 4 drs, 4WD, turbo - some feature GTR specs (eg ATTESSA 4WD)

GTR - 2.6ltr, in-line 6 cyl DOHC, EFI, 2 dr, twin turbo, 4WS, 4WD, ABS, HICAS...

Basic R32 Specification Chart:

Model Engine Type Description Power Output CC Drive Doors GXi CA18i 1.8litre 4cyl 91PS/5200rpm 1809 RWD 4 door

GTE RB20E 2ltr, 6 cyl, single cam 97kw@5600rpm 172Nm@4400rpm 1998 RWD 4 door

GTS RB20DE 2ltr, 6 cyl, double overhead cam 116kw@6400rpm 184Nm@5200rpm 1998 RWD 2 & 4 dr

GTS25 RB25DE 2.5ltr, 6 cyl, DOHC 142kw@6400rpm 231Nm@4800rpm 2498 RWD 2 & 4 dr

GTSt RB20DET 2ltr, 6cyl, dohc, turbo 160kw@6400rpm 263Nm@3200rpm 1998 RWD 2 & 4 dr

GTS4 RB20DET 2ltr, 6cyl, dohc, turbo 160kw@6400rpm 263Nm@3200rpm 1998 4WD 2 & 4 dr

GTR RB26DETT 2.6ltr, 6cyl, twin turbo 208kw@6800rpm 368Nm@4400rpm 2568 4WD 2 dr

Decifering the Engine name:

RB - series of engine 20 / 25 / 26 - capacity (20~1998cc / 25~2497cc / 26~2597cc) D - Double Overhead Cam (or DOHC) E - EFI (Electronic fuel injection) T /TT - Turbo / twin turbo

Engine Type:

The R32 generally featured the RB series of engine in all instances except for in the case of the R32 GXi which feature the CA18i engine. This was a four cylinder, 1.8 litre normally aspirated engine.

Special models:

During and after general production, a handful of special models were released in small numbers. These rare cars generally featured a small variation from the normal, and seemed to be more like test models than anything. The Autech R32 is an example of this. The Autech R32 was tuned by Autech and was basically a four door R32 GTR, without the turbos, as it housed an RB26DE in its engine bay and an automatic gearbox. You can deduce from the name that the engine was a 2.6 litre DOHC EFI in-line six normally aspirated variant. Very good for pulling trailers since they have tonnes of torque.

Link to comment
https://www.sau.com.au/forums/topic/307099-r32-r33/#findComment-5074486
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...