Jump to content
SAU Community

Recommended Posts

Hey,

Stock, the Nissan turbo regulator applies a 1:1 change in fuel pressure along with manifold pressure.

Fuel pressure is negated by boost so the net effect is 43psi of fuel pressure regardless of boost/vac.

Some example figures (sorry about underscores):

base___manifold__fuel____net fuel___when

43psi__-7psi_____36psi___43psi_____idle (i.e. manifold vacuum)

43psi___0psi_____43psi___43psi_____no boost, no vac

43psi___20psi____63psi___43psi_____20psi boost

A rising-rate regulator does a different thing - changes fuel pressure by some multiplier other than 1 along with boost; both the rate and the threshold "it starts working at" may be adjustable.

Corky Bell claims to have brought the "original" rising-rate regulator to the market according to Corky's comments on FPR

Some of his regulators are designed to workalongside the existing regulator, some replace it completely.

For example, the rate might be set to 2:1 and the threshold, 0psi of boost. Then we have some example figures:

base___manifold__fuel____net fuel___when

43psi___-7psi____36psi___43psi____ idle (manifold vac, no regulator action)

43psi____0psi____43psi___43psi____no boost, no regulator action

43psi____1psi____45psi___44psi____1psi boost, +2psi fuel pressure, +1psi net extra fuel pressure

43psi____20psi___83psi___63psi____20psi boost, +40psi fuel pressure, +20psi extra fuel pressure

Cheers,

Saliya

Forget about manifold pressure, i'm referring to the actual pressure that you'll see with a gauge inline. Max fuel pressure is approx 40psi or so, the pumps don't pump it any harder than that I thought, maybe I need to read up on rising rate regs, even with the return line clamped you'll see 40 psi max so how can extra pressure be available (someone explain) ??? All that little vacuum line does for a FPR is lift a valve of its seat no extra pressure is pumped into the system its just a sealed diaphragm.

Mate I think you should go have a read on how fuel systems work before you hand out advice. 80% duty cycle is preferred and its well documented why, fuel pressure regs do increase/decrease fuel pressure depending on the vacuum/boost in the manifold.

Yeah because as soon as you hit 81% duty cycle your engine automatically explodes!!!! :) Do you even know what duty cycle is? You need to put away your fast fours mag and get your hands dirty, my r33 gts-t ran 96% duty cycle for over a year without a problem you going to tell me i'm wrong? And for the record when the FPR has vacuum applied to it the line pressure will be around (from memory) 25-30 psi because the diaphragm lifts the seat and allows fuel back to the tank via a return line so even though the pump is at 40psi the line pressure is much lower than that. Under WOT or boost conditions the FPR is closed bringing line pressure up to 40psi the boost you run on top of that does not change that figure. The boost you run doesn't increase the pressure in the line it just closes it off to lift pressure.

Forget about manifold pressure, i'm referring to the actual pressure that you'll see with a gauge inline. Max fuel pressure is approx 40psi or so, the pumps don't pump it any harder than that I thought, maybe I need to read up on rising rate regs, even with the return line clamped you'll see 40 psi max so how can extra pressure be available (someone explain) ??? All that little vacuum line does for a FPR is lift a valve of its seat no extra pressure is pumped into the system its just a sealed diaphragm.

Yeah because as soon as you hit 81% duty cycle your engine automatically explodes!!!! :) Do you even know what duty cycle is? You need to put away your fast fours mag and get your hands dirty, my r33 gts-t ran 96% duty cycle for over a year without a problem you going to tell me i'm wrong? And for the record when the FPR has vacuum applied to it the line pressure will be around (from memory) 25-30 psi because the diaphragm lifts the seat and allows fuel back to the tank via a return line so even though the pump is at 40psi the line pressure is much lower than that. Under WOT or boost conditions the FPR is closed bringing line pressure up to 40psi the boost you run on top of that does not change that figure. The boost you run doesn't increase the pressure in the line it just closes it off to lift pressure.

wrong, wrong and wrong

as adriano said, clamp the line and fuel pressure will go off the end of a normal gauge with any properly working efi pump. its been said enough times, fuel pressure is referenced to manifold pressure. the reg constantly keeps fuel pressure 43psi above manifold pressure.

if your so certain your reg holds 40psi under boost then try taking the vac line off. if your right it'll be perfectly fine....

Edited by JonnoHR31
Forget about manifold pressure, i'm referring to the actual pressure that you'll see with a gauge inline. Max fuel pressure is approx 40psi or so, the pumps don't pump it any harder than that I thought, maybe I need to read up on rising rate regs, even with the return line clamped you'll see 40 psi max so how can extra pressure be available (someone explain) ??? All that little vacuum line does for a FPR is lift a valve of its seat no extra pressure is pumped into the system its just a sealed diaphragm.

Hi,

This _is_ the actual pressure that you'll see with a gauge inline. Those figures for a stock regulator GTR were read straight off the fuel and boost gauges either side of my wheel.

Yeah because as soon as you hit 81% duty cycle your engine automatically explodes!!!! :) Do you even know what duty cycle is? You need to put away your fast fours mag and get your hands dirty, my r33 gts-t ran 96% duty cycle for over a year without a problem you going to tell me i'm wrong? And for the record when the FPR has vacuum applied to it the line pressure will be around (from memory) 25-30 psi because the diaphragm lifts the seat and allows fuel back to the tank via a return line

I personally don't see a problem with running injectors up to 99.99% provided _all_ mapping points are mapped and the injector manufacturer says it's OK to do so.

However, since it's virtually-impossible to map all load points and correction factors during a tune (e.g. inlet air temp) most people like to leave "some room" for when these things change.

so even though the pump is at 40psi the line pressure is much lower than that. Under WOT or boost conditions the FPR is closed bringing line pressure up to 40psi the boost you run on top of that does not change that figure. The boost you run doesn't increase the pressure in the line it just closes it off to lift pressure.

I get the feeling you don't believe me - put a gauge on your own car, take some measurements, and you'll learn something new. I wouldn't advise popping the vac line off your reg unless you like boost-induced leanouts.

Cheers,

Saliya

Forget about manifold pressure, i'm referring to the actual pressure that you'll see with a gauge inline. Max fuel pressure is approx 40psi or so, the pumps don't pump it any harder than that I thought, maybe I need to read up on rising rate regs, even with the return line clamped you'll see 40 psi max so how can extra pressure be available (someone explain) ??? All that little vacuum line does for a FPR is lift a valve of its seat no extra pressure is pumped into the system its just a sealed diaphragm.

Yeah because as soon as you hit 81% duty cycle your engine automatically explodes!!!! :) Do you even know what duty cycle is? You need to put away your fast fours mag and get your hands dirty, my r33 gts-t ran 96% duty cycle for over a year without a problem you going to tell me i'm wrong? And for the record when the FPR has vacuum applied to it the line pressure will be around (from memory) 25-30 psi because the diaphragm lifts the seat and allows fuel back to the tank via a return line so even though the pump is at 40psi the line pressure is much lower than that. Under WOT or boost conditions the FPR is closed bringing line pressure up to 40psi the boost you run on top of that does not change that figure. The boost you run doesn't increase the pressure in the line it just closes it off to lift pressure.

Go do some reading boosted EFI FPR setups... :(

I personally don't see a problem with running injectors up to 99.99% provided _all_ mapping points are mapped and the injector manufacturer says it's OK to do so.

However, since it's virtually-impossible to map all load points and correction factors during a tune (e.g. inlet air temp) most people like to leave "some room" for when these things change.

The problem is above around 90-95% the injector will be static and completely open anyway. Sure it'll be getting a 0.9 pulse to the injector, but the injector is mechanical and physically can't open and close in the time of the off pulse so anything around 90-95% technically is maxing it out. Depending on the injector you might get some more flow at 100% but it wont be a linear increase, it will drop drop off severely around 90%.

Here is an image to demonstrate what you are likely to see.

93822076.png

So as most people have said, you should always aim for not much more than 80% duty cycle.

Edited by Rolls
wrong, wrong and wrong

as adriano said, clamp the line and fuel pressure will go off the end of a normal gauge with any properly working efi pump. its been said enough times, fuel pressure is referenced to manifold pressure. the reg constantly keeps fuel pressure 43psi above manifold pressure.

if your so certain your reg holds 40psi under boost then try taking the vac line off. if your right it'll be perfectly fine....

I get what you're saying in reference to constant 43psi in relation to manifold, just never seen any factory efi pump get that high( i've looked at quite a few). Obviously i'm wrong, guess you learn something new every day.

Cheers.

P.S for the record I did mention that I might need to be some research in an earlier post, just thought I know how it worked, i didn't, now i do. I'm always open to new info even if I am a stubborn so and so.

The problem is above around 90-95% the injector will be static and completely open anyway. Sure it'll be getting a 0.9 pulse to the injector, but the injector is mechanical and physically can't open and close in the time of the off pulse so anything around 90-95% technically is maxing it out. Depending on the injector you might get some more flow at 100% but it wont be a linear increase, it will drop drop off severely around 90%.

Hey,

Cheers for the data, but if you're mapped for the load/RPM and you have the right AFRs, it doesn't _really_ matter whether the injector is open for 100%, 90%, or 20% - it's still correctly-mapped.

I would assume that if this is a common property to all injectors, the ECU's corrections for "slightly-off-map" points would account for it where extrapolation is required.

As an aside: that graph looks like simple PWM input vs flow output (the ECU's correction for lag time may not be included).

So I still think the idea of "allowing 20%" is antiquated :thumbsup: Maybe someone that does this for a living could step in and provide some real-world data?

I know only what I've seen on my own car(s).

Cheers,

Saliya

Hey,

Cheers for the data, but if you're mapped for the load/RPM and you have the right AFRs, it doesn't _really_ matter whether the injector is open for 100%, 90%, or 20% - it's still correctly-mapped.

I would assume that if this is a common property to all injectors, the ECU's corrections for "slightly-off-map" points would account for it where extrapolation is required.

As an aside: that graph looks like simple PWM input vs flow output (the ECU's correction for lag time may not be included).

So I still think the idea of "allowing 20%" is antiquated :thumbsup: Maybe someone that does this for a living could step in and provide some real-world data?

I know only what I've seen on my own car(s).

Cheers,

Saliya

The 80% is not a hard and fast rule. Its just a guide when you are sizing injectors. That way it gives you a bit of room if you underestimate your requirements.

Cheers for the data, but if you're mapped for the load/RPM and you have the right AFRs, it doesn't _really_ matter whether the injector is open for 100%, 90%, or 20% - it's still correctly-mapped.

Yes this is completely true, sorry my point was more that people should realise that above 90-95% they aren't going to get more fuel. The reason I say this is if say you mapped everything at 90% and it is running fine you might go to yourself "Oh I still have 10% to play with so if we get an extra cold day it will be fine" However as seen from the graph it is a false sense of security, you should be treating 90% as the absolute maximum.

As an aside: that graph looks like simple PWM input vs flow output (the ECU's correction for lag time may not be included).

Yes that is all it is, a very simplistic estimated flow vs PWM output. If you know the open and close time for the injector along with the frequency of the PWM signal I could generate an accurate graph for you.

Personally I think the allow 10-20% is a good rule, whilst you may have tuned your car so that it correctly mapped, you still are guessing for changes in boost and air temp. What if you tuned the car in 10c weather and maxed out the injectors? (lets say a very cold day) and then you go out for a drive in the rain in the hills where the air temp is say 4c and the rain on the intercooler causes it to work far more efficiently? You are almost certainly going to need that 10% of headroom.

Edited by Rolls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...