Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

anything other than da GTR, or bomex. Got nothing against dem just i think u can get them at jetspeed in clayton. anyway. looking for a 400R front dat fits on an r32. Seen plenty on SkylinesDownunder out in New Zealand, but none in Oz. kinda sucks. but yeah, looking at any aftermarket front bar really. Thanks

Is it even possible to ship one fron NZ? if so how much?

eeew u picked the ugliest of the do-luck kits :)

someone in melb with a GTR has that kit on it...

that blue one is a NZ kit... can get them for like 500NZD plus about 150 shipping... so might be a good one as there wont be any in aus

we're lookin at selling the vertex bodykits at around $450 for front bumper, $450 for rear bumper, $300 for side skirts.

Its basically phat n pimp style kit.

i got a family friend that owns glen waverly pannels and he's gonna charge me round $200 to spray the front bar and fit it.

JetSpeed had given me a quote of $350.

anywhere between $200-$300 is a good price from what I was told, just make sure that who ever does it doesn't do a bodge job!

take it easy

Mark

:(

we're lookin at selling the vertex bodykits at around $450 for front bumper, $450 for rear bumper, $300 for side skirts.

Its basically phat n pimp style kit.

Wanna post some pics of that??

you'll need a hybrid sideskirt (halfway down the BNR32 skirt u cut it and then u fibreglass a regular HCR32 sideskirt to it). Unfortunately Vertex dun make GTR kits... wierd I know, but apparently vertex is a dori dori kit maker, and they're one of the major suppliers for D1 cars. Rear bumper should be no probs

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...