Jump to content
SAU Community

Recommended Posts

Had just been for a drive and was standing in front of the car with the bonnet up, when suddenly coolant started spraying out from the back of the engine bay, between the intake plenum and firewall.

Too dark to see much, but i'm guessing a heater hose has burst, and was wondering if anyone had managed to replace the hoses on an RB26 without pulling off the plenum?

Apparently the plenum is a bastard of a job, and after doing the turbos i'm not really keen on having to go through another box of bandaids.

Any advice would be appreciated.

Link to comment
https://www.sau.com.au/forums/topic/308795-rb26-heater-hoses/
Share on other sites

yeah its a prick of a job. give the car and $500 to a workshop and tell them to call when it's done :D

heater hose is not toooooo bad. but there are also 2 coolant lines under the plenum (1 heater, 1 turbo feed) that often die. its all pretty ugly, start with taking the starter motor out, grab the bandaids, and if its still warm grab the burn cream too :)

Thanks Duncan, I had a feeling that would be the case. I'll poke a snakescope under there later today to try and see where the leak is.

The taking it to a workshop plan is sounding good, just not sure if I can get it there without losing all the coolant yet.

The little fellas that designed the RB26 must still be laughing at us. Bastards!

ahh yeah its all easy when the motor is out :D

and no you can't drive it to a workshop you will loose all the coolant in a matter of minutes, even before then it wont be circulating. I never think about that because I always kill the motor/headgasket at the same time because I don't notice the coolant leak....

Duncan,

If you have a minute, can you just confirm these are the 2 hoses I can replace after pulling the starter motor?

post-13979-1266573966_thumb.jpg

And these are the other 2 you mentioned, but they are a plenum off job?

post-13979-1266574030_thumb.jpg

Not likely to be the culprit in my case because they are further forward, but I guess these oil cooler lines could leak as well?

post-13979-1266574109_thumb.jpg

And if it's any of the hard pipes it's plenum off time?

I just ordered a full hose kit, so if I turns out to be one of the hoses in the first pic i'll at least be able to get it running so the workshop can do the rest.

Thanks for your help. :)

hmmm yeah depends what is farked. none of them are easy tho.

the heater hoses are do-able but starter motor out is required. Like Paul said the top bolt is tricky but a stubby 14mm spanner helps heaps. And the top hose in the second diagram is probably doable with the starter out too, we had to change it the other day. one end from below and the other end from above, if the hose clamps are in the right place you can get them.

the ones to and from the oil cooler are do-able to, and the one to the front of the block is pretty easy.

but it is hard to trace and spot what is going on with the plenum on, no doubt. I just bought the silicon hose kit from just jap to change all these myself but we are taking the motor out anyway.

bottom line, if its at the rear of the motor it is either the heater hose or the turbo water line (top one in the second pic). a pain but possible. you will make life easier if you put the rear of the gearbox on a jack and undo the gearbox cross member - creates a lot more space up there.

Thanks Duncan, that makes it all crystal clear.

I noticed that when I undo the radiator cap and break the vacuum seal I can still hear a bit of coolant trickling down somewhere toward the back of the plenum.

Hopefully once I get the starter out tomorrow i'll be able to see where it's coming from, without swallowing any of it.

Thanks again, and if you want some practice fitting a full sillicon kit before you do yours, i'm just down in Canberra....... :)

  • 2 weeks later...

Just an update for anyone with a similar problem who comes across this thread later.

Ended up pulling off the plenum and yes, it is every bit as bad as people say it is. Imagine putting your hands into a box full of feral cats for 5 minutes, same end result.

But on the up side, I was able to replace every single hose that lives under there, which would have been impossible to do from underneath even with the starter motor out. The hose that had actually split was the little bastard coolant line from the turbos, the top hose in the second picture from the previous post.

The JustJap sillicon engine hose kit ($299 + freight) contains 14 hoses, and 12 of them go under the plenum, a mixture of coolant and air hoses. The other 2 hoses go from the heater box on the passenger side of the firewall and back across behind the engine.

There is also a small plastic connector pipe that joins the top heater hoses between the back of the plenum and the firewall. Mine was very brittle and crumbled just from pulling the heater hose off, so definitely worth replacing that while the plenum is off.

hmm I actually had to pull my plenum off the other day in the engine bay too....medalist tools make some wonderful ring/ring spanners in a C or S shape, they were perfect for undoing the bolts underneath the plenum from above....wonderful things.

I managed to get all of the bottom plenum bolts off with a 1/4" drive socket and a couple of wobble extension bars.

Getting the washers and nuts back onto the lower studs looked like it was going to really suck until I got the idea to temporarily glue each set of washers and nut together into a stack with a few drops of nail polish first. Just popped them nut first into a magnetised 12mm socket and carefully guided them onto the studs. Worked a treat.

I managed to get all of the bottom plenum bolts off with a 1/4" drive socket and a couple of wobble extension bars.

Getting the washers and nuts back onto the lower studs looked like it was going to really suck until I got the idea to temporarily glue each set of washers and nut together into a stack with a few drops of nail polish first. Just popped them nut first into a magnetised 12mm socket and carefully guided them onto the studs. Worked a treat.

little smear of ARP moly lube works a treat to do the same thing....great thinking outside the square and using some of your nail polish though :)

little smear of ARP moly lube works a treat to do the same thing....great thinking outside the square and using some of your nail polish though :D

Hey, it was my daughters nail polish.

I wouldn't be seen dead in that shade of lilac :laugh:

  • 3 years later...

Thread revival! I want to change all hoses while the engine is out - just looked on JustJap and can't see this engine hose kits - does anybody know of a kit that is the same? Seem to be a few on ebay just not sure if they are the right ones?

Something like this....

http://www.ebay.co.uk/itm/SILICONE-Radiator-Heater-HOSE-fit-for-Nissan-skyline-GTR-R33-R34-RB26DET-BL-/281111064023?pt=Motorcycles_Parts_Accessories&hash=item4173866dd7

The JustJap sillicon engine hose kit ($299 + freight) contains 14 hoses, and 12 of them go under the plenum, a mixture of coolant and air hoses. The other 2 hoses go from the heater box on the passenger side of the firewall and back across behind the engine.

Edited by ab20000

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...