Jump to content
SAU Community

Recommended Posts

i installed my cd player a few wks ago and whilst doing so i lost back up power, so everytime i turn the car off, everything looses memory and resets, its driving me insane.

im sure i heard a fuse blow but i cant find where, i think i have looked everywhere.

any 1 got an idea?

Link to comment
https://www.sau.com.au/forums/topic/310881-r33-looses-memory-no-back-up-power/
Share on other sites

i installed my cd player a few wks ago and whilst doing so i lost back up power, so everytime i turn the car off, everything looses memory and resets, its driving me insane.

im sure i heard a fuse blow but i cant find where, i think i have looked everywhere.

any 1 got an idea?

Mike

I'm gonna assume that you've had the memory problem since installing your CD player

the usual cause is the constant and Acc wires crossed over (there the red and yellow ones) swap them round you should be sweet

if the above assumption is wrong the the fuse is near your right knee

cheers

when you say everything, do you mean the clock in the dash as well? if so then as bundybear said, check the fuse panel on the right hand side of the steering wheel down near where the lever is to pop the bonnet. just pull them out 1 at a time and see if they are any blown.

also might be worth pulling out your stereo and just unplugging it then turning the car on and off to see if the clock is still losing it's memory.

if it is only the cd player losing it's memory then check the wiring

The same thing has happened to my R32... My cd player wont turn on at all, the clock wont display the time at all and my aircon loses its memory also. I checked the fuses and one was blown, so i tried putting another 10amp fuse in and it blows straight away. It all started when i took my car in to get the compressor bearing fixed and my mechanic has shorted something out but i cant figure what hes done.. :no:

i have checked every single fuse in the car and i cant find a blown one, the only reason my cd player is working is cause i wired constant with accessories for the time being until i find the solution, believe me i wouldnt be asking if i could find the fault.

And yes EVERYTHING looses memory, A/C, Clock, Turbo Timer, CD Player.

sly-01 which fuse keeps blowing in your r32?

mic

you've obviously lost the constant feed to the entire dash (probably ECU, dash lights also).

I know the 32'z have a fuseable link (not fuse, they look like a loop of wire) near the battery this might have gone

with no wiring diagram 4 the 33'z I'd grab a test light and start pokn round

check the back of the Ignition switch 4 constant power (make sure plugs arn't loose 2) it'l give you an idea where 2 look

where bouts you located ?? maybe someone familiar with autoelec in your area can help

cheers

ps you know there are 3 lots of fuses ....

mic

you've obviously lost the constant feed to the entire dash (probably ECU, dash lights also).

I know the 32'z have a fuseable link (not fuse, they look like a loop of wire) near the battery this might have gone

with no wiring diagram 4 the 33'z I'd grab a test light and start pokn round

check the back of the Ignition switch 4 constant power (make sure plugs arn't loose 2) it'l give you an idea where 2 look

where bouts you located ?? maybe someone familiar with autoelec in your area can help

cheers

ps you know there are 3 lots of fuses ....

yep i know there are 3 lots of fuses, under bonnet, under steering wheel and boot. i will search for that link fuse

im in mango hill, brisbane

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
×
×
  • Create New...