Jump to content
SAU Community

Recommended Posts

:(list of some parts and standard items i wish to sell from build-up :worship:

- standard radiator from s2 R33 RB25DET excellent condition $150 SOLD

- standard s2 R33 RB25DET block no head, block is in excellent condition, $800 SOLD

- Gizzmo IBC Electronic Boost Controller excellent condition comes with everything $250

- standard in-tank fuel pump s2 R33 very good condition $50 SOLD

- s2 R33 RB25DET auto-trans + pedals excellent condition stage 2 shift kit been serviced new filter trans-fluid etc from mike at M.V. automatics $500ono

- s2 R33 RB25DET impul auto ecu removes speed limit cut rev limiter goes to 7.200rpm i think been awhile since i have been on the dyno give or take boost cut removed or moved i was running 14.3psi excellent condition $200

- 2x standard boost solenoids good condition $15 each

- s2 R33 whole complete A/C from the engine bay ill check with my mechanic excellent condition $400ono

1 x Brand New Blue Castor Rod Bushes noltec or nolethane $65 pick-up or $70 posted.

1 x complete set off standard R33 s2 brake lines front + rear used but in fine condition no splits kinks etc $50 pick-up or $55 posted.

2 x standard R33 rims good for drifting etc camber wear on tread $70 pick-up only.

................................................................................

.................................................................................

...........................

measurements in INCHES for thermal flex left overs...

1 x Thermal Flex (RED) 8" long X 2" wide------------------------ $15

1 X Thermal Flex (BLUE) 6" 1/2" long X 2" 1/2" wide------------ $15 ------------$60 for all 3 pick-up or $65 posted

1 x Thermal Flex (BLUE) 13" Long x 3" Wide--------------------- $30

................................................................................

.................................................................................

.............................

1 x i believe its the heater unit minus the heater core $60 pick up or $70 posted.

1 x i got this from a group buy a while back black faced 300km/h speedo set in psi no 300km/h tho i have it in my car but i put the 180km/h speedo with the set, boost gauge on tachometer is in psi and oil pressure is in psi as-well + new hot/cold gauge and fuel level so everything except the 180km/h is new the set cost me $100 + postage so i guess it would be fair to ask for $50 pick-up or $55 posted.

1 x 1996 s2 R33 rb25det Throttle body good condition $60 pick-up or $65 posted

1 x R33 Skyline Standard Genuine Nissan Dump Pipe $30 pick-up or $35 posted

1 x R33 s2 Skyline nissan genuine rubber intake pipe used, good condition no perishing, comes with stock BOV plumb back hose $50 pick-up or $55 posted

1 x s2 R33 Cross Over pipe with b.o.v. $55 pick-up or $60 posted

1 x R33 s2 Original Nissan intake manifold (plenum) comes with top and bottom half rubbers, bolts, everything needed to fit it up., no cracks or leaks, reason for sale is put greddy intake on. $75 pick-up

6 x s2 R33 GTST 370cc injectors, all working when taken out of car, just been removed for nismo injectors these have only just been taken out and are all in 100% working and flowing condition!! comes with rail. $150 pick-up or $155 posted.

most items can be posted some cant...

contact me on here or e-mail me at ([email protected]) or call me on (0401409575Allan)

i will start uploading some pictures tonight if i have got some time..

All items located in : Adelaide,SA

Contact me on (0401409575 Allan) or pm-me parts can be delivered via freight/courier at your expense or pick up in Adelaide,SA parts are with my mechanic so can organize it any-time.

most prices are negotiable.!

Regards.

Allan.M

1 x R33 s2 Skyline nissan genuine rubber intake pipe used, good condition no perishing, comes with stock BOV plumb back hose $50 pick-up or $55 postedSOLD

1 x Thermal Flex (RED) 8" long X 2" wide------------------------ $15

1 X Thermal Flex (BLUE) 6" 1/2" long X 2" 1/2" wide------------ $15 ------------$60 for all 3 pick-up or $65 posted SOLD

1 x Thermal Flex (BLUE) 13" Long x 3" Wide--------------------- $30

- s2 R33 RB25DET impul auto ecu removes speed limit cut rev limiter goes to 7.200rpm i think been awhile since i have been on the dyno give or take boost cut removed or moved i was running 14.3psi excellent condition $200 SOLD

- s2 R33 RB25DET impul auto ecu removes speed limit cut rev limiter goes to 7.200rpm i think been awhile since i have been on the dyno give or take boost cut removed or moved i was running 14.3psi excellent condition $200 SOLD

back up for sale due to time waster

................................................................................

................................................................................

.

...........................

measurements in INCHES for thermal flex left overs...

1 x Thermal Flex (RED) 8" long X 2" wide------------------------ $15

1 X Thermal Flex (BLUE) 6" 1/2" long X 2" 1/2" wide------------ $15 ------------$60 for all 3 pick-up or $65 posted

1 x Thermal Flex (BLUE) 13" Long x 3" Wide--------------------- $30

................................................................................

................................................................................

.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...