Jump to content
SAU Community

Greddy Emanage Ultimate Cheap Cheap

chef_stagea
 Share

Recommended Posts

chef_stagea Grand Master

chef_stagea

Posted
Posted

i have an emanage ultimate with direct plug and play loom (n4)

these looms are few and far between... no splicing and sus ecu wiring needed

timing control, fuel and air map control... boost is possable with the addition of a boost sensor ($120 or so)

SENT AUS WIDE $750

Msg me 0400099986 or PM thanx

Link to comment
https://www.sau.com.au/forums/topic/311906-greddy-emanage-ultimate-cheap-cheap/
Share on other sites
jbrnr21 Apprentice

jbrnr21

Posted
Posted

hey mate, any chance of a pic on here???

if not can you send one to [email protected] please, also do you have wiring diagram for this item as i will be puting it in my vl with the rb25det conversion.

thanks

chef_stagea Grand Master

chef_stagea

Posted
  • Author
Posted
hey mate, any chance of a pic on here???

if not can you send one to [email protected] please, also do you have wiring diagram for this item as i will be puting it in my vl with the rb25det conversion.

thanks

here ya go mate... its just a matter of getting the 2 big rectangle plugs... one goes to your ecu, the other goes to the plug currently pluged into yout ecu... the wiring diagram is on the greddy website and here... ill get onto it now for you tho...

what state you in??

UnCo Rising Star

UnCo

Posted
Posted
Just doing some research on these units, to runtjis unit in a gtr you need to change 2 wires around and ground one. I've got the diagram

Hey mate, what exactly needs to be done to fit this to a GTR?

I thought the N4 loom fits GTR?

Cheers

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Butters
      No engine fan = quieter getrag ???

      By Butters · Posted

      Saw this video today from Adam LZ.    Long story short is he is claiming that the load from the engine fan once the fan clutch heats up(engaged) is increasing the getrag rattle(at idle) when you don't have a dual mass flywheel.  Before I go buying an electric fan setup .... Anyone heard of this ?    I must admit when my car is cold the getrag is pretty quiet and I do notice the rattle after it is all warmed up. I've always assumed this is due to the gearbox oil temp and tolerances of metal.       
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Yep it sure does.   Tone wheel lines up in the same spot perfectly.    
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Something I meant to say when we were chatting the other night about having an open trailer floor being great to work on a car, but you've never used the feature... It's a great place to park a car after doing suspension component changes, and do the tightening of all the bushes with the car sitting at full ride height. Especially when you don't have a 4 post hoist!
    • GTSBoy
      Duncan's V37.......race car?

      By GTSBoy · Posted

      That is way more science than even I would use. I just eyeball it, not even accounting for the non-verticality of the tape measure when held on the lip and the centre at the same time. +/- 2mm is good enough for the girls I go out with.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, before putting them in I need to understand the stock ride height. This is how I measured it: First, check the diameter of the wheel's centre cap, it was 52mm. Then put a piece of masking tape approximately across the centre and measure 27mm (half) from at least 3 sides to get a reasonable idea of the centre of the wheel cap. Mark that with a horizontal line as one measuring point. Then, directly above the wheel on the guard, put another piece of masking tape in approximately the centre. Use a string line to find out the point on the guard above the centre of the wheel cap and mark that. Then it is simple, just a tape measure to check the distance from centre of the wheel to the centre of the guard. Final results where  LF: 381mm RF: 379mm LR: 401mm RR: 400mm Pretty even considering they are 120,000klm old factory springs, lets call that 380 front and 400 rear.
×
×
  • Create New...