Jump to content
SAU Community

Recommended Posts

http://forums.skylinesdownunder.co.nz/show...&threadid=29881

Interesting to see you read the same post Merli. Hehehe

So did you pay $1800 for it Mirkop and now trying to make the big profit or was the $1800 post just full of :bs!:

Cheers

Ken

Link to comment
https://www.sau.com.au/forums/topic/31205-os-giken/#findComment-630718
Share on other sites

well if you people havnt realised there isnt just one type of OS giken clutch, the are 3 types. and all 3 have differnt power ratings. i can still get anyone on this website a new os giken twin plate for $1800 if they like a power rating of only 300 horses. where as this one has a power raing of over 700. so maybe BIGBLOCKR31COUPE and gtrken should get their facts right befor posting. it would just ake you look a little smarter, if that is possible...

Link to comment
https://www.sau.com.au/forums/topic/31205-os-giken/#findComment-631157
Share on other sites

You're right. There are three types of twin plate OS Giken clutches.

TS2B - Pressed Steel Cover, Twin Plate, 204mm Clutch Plate Diameter.

TS2BD - Pressed Steel Cover, Twin Plate, 204mm Clutch Plate Diameter, Sprung Center.

TS2CD - Pressed Steel Cover, Twin Plate, 215mm Clutch Plate Diameter, Sprung Center.

osst.gif

Japanese Retail Prices are as follows:

TS2B - 143,000 Yen

TS2BD - 148,000 Yen

TS2CD - 158,000 Yen

Link to comment
https://www.sau.com.au/forums/topic/31205-os-giken/#findComment-631260
Share on other sites

You're right. There are three types of twin plate OS Giken clutches.

TS2B - Pressed Steel Cover, Twin Plate, 204mm Clutch Plate Diameter.

TS2BD - Pressed Steel Cover, Twin Plate, 204mm Clutch Plate Diameter, Sprung Center.

TS2CD - Pressed Steel Cover, Twin Plate, 215mm Clutch Plate Diameter, Sprung Center.

osst.gif

Japanese Retail Prices are as follows:  

TS2B - 143,000 Yen

TS2BD - 148,000 Yen

TS2CD - 158,000 Yen

So what your saying merli is the cheap one that Mirkop is talking about is

143,000 yen which is about $1800 and the one he has for sale is the

158,000 yen one which is about $2025?

Or am I just stupid like Mirkop suggests...??

hehe

Cheers

Ken

Link to comment
https://www.sau.com.au/forums/topic/31205-os-giken/#findComment-631368
Share on other sites

So what your saying merli is the cheap one that Mirkop is talking about is  

143,000 yen which is about $1800 and the one he has for sale is the  

158,000 yen one which is about $2025?

Or am I just stupid like Mirkop suggests...??

hehe

Cheers

Ken

I'm glad someone was able to draw the obvious conclusion that I was hinting at bigthumb.gif

There ain't $1200 difference between the three different OS Giken twin plates mikrop.

Link to comment
https://www.sau.com.au/forums/topic/31205-os-giken/#findComment-631475
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Thanks for that mate always a good help
    • It's not really a calibration issue, if the voltage is really at 2V. If the voltage is 2V, then that's what the TPS is putting out, and the Haltech is seeing that and 2V is about 40% open (you know, between 0.45v being closed and something close to 4.5V being fully open). So, that would suggest that the TPS is maladjusted, on crooked, something something something. Or a wire problem.
    • Hi guys my TPS voltage is reading over 2v at idle.  My Haltech ECU is reading around 40% throttle position at idle also which is really strange. Note the actual throttle position sensor is brand new…    anyone have any experience with this or know how to calibrate it on Haltech ? 
    • The OEM disk will not work on any AEM ECU, you need to use the one they made. You shouldn't have to flip the CAS or whatever you were describing, if you set the ignition sync offset correctly it can't backfire. Make sure you're using a spark plug lead on coil 1 instead of the timing loop to avoid weird issues with the timing light. Double check that your timing settings are actually correct, like is the 24 tooth configured correct or should it actually be 12 teeth for 1 crank revolution? I also found this: 305817248-AEM-Undocumented-Settings-v1-2.pdf    
×
×
  • Create New...