Jump to content
SAU Community

Phillip Island Classic 2010

willL

By willL,
in Victoria

 Share

Recommended Posts

Silhouette31 Rising Star

Silhouette31

Posted
Posted

made the trek from adelaide to help pit crew the dr30's debut race since 1987.

did really well. the gtr's had a couple of issues, the baffles in the tank of terrys car in race 3 disintegrated and was picked up into the fuel pump and filter.. also the fuel rail popped off of the dr30 during practice on friday, scary moment but other than that it ran beautifully considering its been parked for nearly 20 years.

have hundreds of photos i have to upload from the pit wall and around the dummy grid etc. was a great experience.

BBGTR Experienced

BBGTR

Posted
Posted
In the Friday qualifying session Terry clocked a 1:44.9819! thats one for track guys who are going to phillip island in april for the wrx club day to think about... :)

Gimme 10inch slicks and 300 less kilos (about the weight difference to my car) and I'd be pretty confident! ;)

JAGR33 Grand Master

JAGR33

Posted
Posted
In the Friday qualifying session Terry clocked a 1:44.9819! thats one for track guys who are going to phillip island in april for the wrx club day to think about... :)

That's quick. Almost as quick as Aaron (Aaron34) in his R34 GT-R.

http://www.sauvic.com.au/lap_records

:blink:

cazz Rising Star

cazz

Posted
Posted (edited)

See the thread on what the DR has been doing here

http://www.skylinesaustralia.com/forums/Ge...in-t313783.html

Car will be left as raced, and not restored. It does have to have some paint repaired after the fire.

This was Rod Marklands first outing in the GIO GTR after his HR31. He was having trouble adjusting to the car, which I think is understandable. He spun in Race 4 at the end of the straight.

Terry had fuel pickup issues in race three, after the foam in the fuel cell started breaking down.

The HR31 has been sold to a local fellow, who will be bringing it out to play with us at most of the future events.

The RX7 wasn't disqualified, but his position wasn't logged, as the car didn't have a log book.

This is an awesome event, heaps of people on the Sunday, and lots of folks thrilled to see the GIO GTR and the DR back out there again. I couldn't beleive how popular the DR30 was.

As always the Winfield number 1 car was immaculate. I am so in awe of this car.

I had a ball, and thanks to all the helpers, and people who travelled from Adeladie to give me a hand with the car.

Edited by cazz
scotty nm35 Grand Master

scotty nm35

Posted
Posted

Hi Cazz, i'm glad its out racing again, it is what it was built for after all. That little bit of yellow under the bonnet just adds to the race car look, I wouldn't worry about it. :O

Someone did a great job cleaning up all that dry powder, messy stuff and gets everywhere.

I saw a crazy Skyline lady getting into the red R35, was that you?

cazz Rising Star

cazz

Posted
Posted
Cazz, the DR is jsut awesome, watched those youtoobs and i tellya... im a fan!!!!

I love the noise from the gearchanges. If you watch Seto driving his DR at Bathurst 1987 in the wet, his car makes exactly the same noises. Going to be really interesting to see if I can actually change gears in this thing lol.

I have just loved the DR's since I saw Gavin's car. Until then, I didn't know much about them, but what a tough little car they are.

Priestley Rising Star

Priestley

Posted
Posted
Craig at the wheel of the DR, slamming the dogbox into gear. :O

Good videos there. If I'd known this event was on I probably would have headed down to watch.

I imagine the guy in the VL was in need of a new pair of underwear after that off!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...