Jump to content
SAU Community

Recommended Posts

Set of four Starform wheels (these are a high quality jap copy of German BBS mesh style wheels) - see pic below.

Front 17x8", +40mm offset, 225/45 tyres

Rear 17x9", +45mm offset, 245/40 tyres

5 stud - the offsets suit R33, 200SX, 300ZX and Supra (I had them on my R33).

Excellent condition - minor kerb scrapes on a couple.

Asking $1,300 total including nuts & locknuts, but I would prefer Adelaide buyers who can inspect and collect in person.

Link to comment
https://www.sau.com.au/forums/topic/31468-fs-jap-17-wheels-tyres/
Share on other sites

those tyres rock!!! they are the first set of tyres i've used that hook up even when taking off with a little grunt i had dunlop lemanz and could fry em at 60km easy but no chance with the contisports....perform very well in the wet as well!!! i might snap em up for the cressi if i get a little money left ova

1/ Do these rims fit on the front, without having to 'shave' ANY part of the front calipars?

2/ Would you consider these to be a lightweight rim, or are they at least lighter than the stockies? I have 19's but am starting to do some track work, and these are too heavy and tyres are too expensive to burn.

Al - To put them on the front of my R33, I used thin spacers to avoid having to shave anything off the calipers. I can provide these if required. The rims weigh about the same as stock 16" rims, but of course the 17" tyres would be a bit heavier. I can weigh the two together and get back to you if you want.

Matt - just got your PM - I will call you tomorrow.

  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...