Jump to content
SAU Community

Recommended Posts

Hi everyone, my r32 has an rb25det conversion done by previous owner. I have owened it for about two weeks now. I have done the usual services, oil change, auto trans flush and new spark plugs. Now the thing I am noticing is when under hard acceleration it wont boost past 6.5lb or seven if I'm luckily, its okay reving through the low to Med range but as soon as the revs get high it feels like its spitting or missing, when I take my foot off the the gas a little it kicks back in, slightly. I have checked all vacume lines I could see, which are all silicon hoses with no ties? The coil packs are stock as far as I can see but I would like to find out if it could be more basic before I fork out the cash for new coil packs. Any help would be great or directions to similar threads.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/
Share on other sites

Might help to tell us how much boost you SHOULD be running mate lol. 6-7psi is normal for 25s if my memory serves me correct...

Have a look for an exhaust leak, and/or boost leak.

Boost leak can indeed cause your missing/spitting, and an exhaust leak can cause a lack of boost/laggy feel

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5162762
Share on other sites

Lol sorry I'm running a gizzmo EBC. Set to 9.7lb, I noticed that the silicone pipe that connects the intercooler pipe to the factory inTake pipe on top of the motor has a tiny gap on either side of the tube, I'm not sure if this is due to them being over tightened or the clamps are not closing strait. How much gap would it take to loose that much boost? As far as the exhaust goes it factory dump pipe to 3" cat back. My mechanic put it up on the hoist and did not notice any exhaust problems, it looks pretty new actually.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5162792
Share on other sites

Yeah even the tiniest of leaks can cause a mass fire in RB engines, because they are MAF sensored...

Do you have a pic of said silicone coupler?

How old are your spark plugs?

They could be fouled and not firing properly, the boost is blowing out the poor spark if so, this would prevent your engine from making more boost.

Go through the length of your exhaust and check for studs that are loose, specifically the head-manifold and manifold-turbo ones.

Other than that, have a look at your spark plugs, replace that silicone coupler if it looks like its leaking, and double check all the vacuum hoses and electronics are working for the EBC. Maybe even try to disconnect the wastegate actuator and take it for a spin. Watch your boost gauge very closely and see if you can boost above 7psi. Not the safest method, but it will rule out if your EBC is the problem...

Good luck bro!

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5162824
Share on other sites

Oh and do just diconnect the actuator from the solenoid or do I need to block it up?

I would leave the actuator alone you can just turn your boost controller off and that should run wastegate pressure, would be a lot safer.

Still sounds like it could be coils, what gap is your plugs? 0.8mm is the standard most people run with standard coils.

Other than thats if its pulling smooth but boost is tapering off would just likely be able to fix that by playing with the settings on the boost controller.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5162861
Share on other sites

Ok, I have bypassed the EBC and noiticed it still holding boost but still maxing out at 5 sometimes 6lb. It doesn't "seem" to be plaining out or spitting now but there was a fine line between it spitting and not spitting.

what could be going wrong with the ebc? Could it have dual high and low settings

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5163195
Share on other sites

Okay, I have installed all new clamps on piping and ties on vac lines. Now its hitting boost a lot better but its still spitting, it only seems to do it when putting my foot right down, but not when i accelerate just a little, so I'm assuming that's why its still not hitting its full boost.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5163412
Share on other sites

Dang namit! I think this could be my problem. The plugs I was recommended by the ngk book were BCPR6ES, standard copper. but the plugs I pulled out are BKR5EIX, iridium. Now which ones should I be using? BKR5 or BCPR6? Also what is the difference between the two? Besides being copper and iridium.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5164257
Share on other sites

Dang namit! I think this could be my problem. The plugs I was recommended by the ngk book were BCPR6ES, standard copper. but the plugs I pulled out are BKR5EIX, iridium. Now which ones should I be using? BKR5 or BCPR6? Also what is the difference between the two? Besides being copper and iridium.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5164258
Share on other sites

The 5 and 6 (i.e. the number) is the heat rating of the spark plug. The higher the number, the hotter the plug, and warmer plugs are used for turbo cars because boost causes more combustion chamber heat. If your book recommends you run the 6s, and your current plugs are 5s, then this would certainly be your problem...

Make sure they are gapped correctly though, the gap should be listed in the NGK book you've been reading.

Link to comment
https://www.sau.com.au/forums/topic/314912-loosing-boost/#findComment-5164436
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...