Jump to content
SAU Community

Good Double Din Unit

Ericjayrol

By Ericjayrol,
in Car Audio & Electrical

 Share

Recommended Posts

Ericjayrol Community Regular

Ericjayrol

Posted
Posted

hey,

Im looking at upgrading the stock system in my R34, I want to get a double din so it fits in nicely as a nice and easy replacement to the stock unit.

I want it to have front USB and some connectivity to the Iphone, whether its a dock or just the ability to use the cable and sit it in the cup holder.

I want good quality audio aswell obviously, and want something cheap enough, no more than $600

I plan to further upgrade by amplifying the stock system and putting in a sub.

Any advice on a good head unit to match my needs? Also, ideas for the good sub and amp set up would be nice

Link to comment
https://www.sau.com.au/forums/topic/317917-good-double-din-unit/
Share on other sites
Ericjayrol Community Regular

Ericjayrol

Posted
  • Author
Posted

Is that so? So I made the right decision then :happy:

Yeah, they are incredible!

I went with the:

CDE-102E headunit - 2 preouts with subwoofer control, 50W x 4, mp3/wma/aac playback, front usb & aux, rear ipod/iphone

SPR-17S component 2 way speaker system - 330W peak 110W RMS, 6 1/2"

MRP-F600 4 channel power amp - 1320W max, variable high pass/low pass crossover, bass eq, speaker level input, 150W RMS x 4 2Ω, 14.4V

I don't know the info of the sub, but its the matching one for the rest of the system.

Let me know what u all reckon, it cost me $2000 with professional installation and all the amp wiring kit and all that.

KrazyKong Proficient

KrazyKong

Posted
Posted (edited)

I installed a JVC KDR606 head unit into my Skyline that I had saved from my previous vehicle. I'm still learning things about audio, but it seems to have near similar specs to the Alpine CDE-102E unit. It only has one set of preouts however, but I havn't gotten to the part of looking at amps or subs just yet. I think it cost me $250. I remember reading on here about someone trashing JVC products and saying they were total crap. I hope mine isn't a crap one. I sounds good, works great with usb and seems to put out some nice power for the speaks I do have in the car. Anyone else used this unit?

09040803e07c29.jpg

Edited by KrazyKong
Ericjayrol Community Regular

Ericjayrol

Posted
  • Author
Posted

The JVC looks nice, Ive heard a lot of people trash them aswell, but all the JVC systems i've heard sound all sweet.

Maybe the cheaper JVC units just aren't all that good, but thats to be expected with anything cheap

  • 2 months later...
08yannch Rising Star

08yannch

Posted
Posted
Is that so? So I made the right decision then :laugh:

Yeah, they are incredible!

I went with the:

CDE-102E headunit - 2 preouts with subwoofer control, 50W x 4, mp3/wma/aac playback, front usb & aux, rear ipod/iphone

SPR-17S component 2 way speaker system - 330W peak 110W RMS, 6 1/2"

MRP-F600 4 channel power amp - 1320W max, variable high pass/low pass crossover, bass eq, speaker level input, 150W RMS x 4 2Ω, 14.4V

I don't know the info of the sub, but its the matching one for the rest of the system.

Let me know what u all reckon, it cost me $2000 with professional installation and all the amp wiring kit and all that.

looks like a pretty good setup. we what pictures NOW

just a couple of things 150W RMS x 4 is for 2Ω a 4Ω load results in less power

and what is powering the sub

Ericjayrol Community Regular

Ericjayrol

Posted
  • Author
Posted

The sub is being bridged on the amp, the set up only has front speakers, no rears.

I know it seems incomplete that way, but its a very good set up and sounds clear with enough bass from the sub that I really didn't wanna bother getting rears.

Wouldn't be much in the way of photos, the door speakers are covered with stock covers, the sub is sitting in the boot in a box, the amp is connected up to the rear of the flip down middle seat and there's the head unit ofcourse, if you still want photos I can take some, but I don't think its anything special in the way of appearance.

linkems Collaborator

linkems

Posted
Posted
The sub is being bridged on the amp, the set up only has front speakers, no rears.

I know it seems incomplete that way, but its a very good set up and sounds clear with enough bass from the sub that I really didn't wanna bother getting rears.

Wouldn't be much in the way of photos, the door speakers are covered with stock covers, the sub is sitting in the boot in a box, the amp is connected up to the rear of the flip down middle seat and there's the head unit ofcourse, if you still want photos I can take some, but I don't think its anything special in the way of appearance.

Rears are just fillers and they days of 6x9s in the rears are long gone. Too much noise from the rear ends up ruining the sound quality. Most sound quality competition cars don't use rears and if they do it is a very faint sound stage should be coming from the front.

southlander Apprentice

southlander

Posted
Posted

no rears? thats crazy talk. a good set of rears gives balance to the system and what if you have passengers? dont be cheap. personally i like pioneer head units with kicker/ jl speakers and subs and jl amps. soundstream used to be great but have gone wayyyy downhill. i have always run 6" slpits in the front and rear and they've been awesome systems.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...