Jump to content
SAU Community

Recommended Posts

Hi All,

I've been reading through the parts numbers thread/DIY service thread etc, but there are a few things I can find.

I've found a Dayco timing belt (PART No: KTBA173) but it doesn't list that it fits the RB25DET Neo. It lists RB20DET, RB25DE, RB26DETT. I would assume that it would fit the 25DET also?

Also, how many litres do the auto trans hold? I want to make sure I have enough fluid to cover a flush as well as a fill.

Any idea on where to get rear wheel bearings and wheel studs from in Bris? Right rear wheel bearing is making some unhappy sounds and one of my LH rear wheel studs sheared off.

Cheers

Scott

Link to comment
https://www.sau.com.au/forums/topic/318428-s2-stagea-servicing/
Share on other sites

Can't help you with the parts as i'm in NZ but you need 12 -14L to do the auto so best bet is to look for a 20L drum of quality synthetic atf and you can use it for the Atessa and power steering as well.

Some stuff i dug out of the DIY thread (parts list):

S2 wheel studs #43222-70T00

OK Series 2 part numbers are:

Water Pump 21010-AA526

Timing Belt 13028-5L327

Tensioner 13070-5L300

Idler 13074-58S00

Nissan rear wheel bearing ass c/w bracket 43210-AA100

Possible cheaper alternative:

New part number for rear wheel bearings to suit s2 auto . CBC Bearings carry these .

Kit NJ246.

To suit, 200sx 7/94-2003

Skyline 6/91-3/93 2.0L

Skyline 6/91-3/93 2.6L 4 stud only

Skyline 8/93 on 2.5L

Skyline 8/93 on 2.6L 4 stud only

Best part is the price $154.00 incl gst. The genuine nissan price was $323.00.

Thanks Bob, I found that too. Just don't know if CBC Bearings is Aus wide or not.
It would appear so:

http://www.google.co.nz/#hl=en&source=...1aa81ab65bd61af

and the cam belts appear to be all the same: 25, neo, 26

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good tips, will get on those tomorrow. When doing the maintenance I did move a few of those connectors around, and things that are old tend to not like moving around. (Like me).
    • Don't try it. It will be shit. Better chance of damaging the engine than gaining any knowledge about the old one. Maybe, but unlikely, especially if the O2 sensor is working. You can use NissDataScan to look at the stock ECU.   Cleaning the AFM is seldom necessary and seldom helps. The R35 coil & loom conversion should eliminate dud coils or plugs. But as you still have misses - look to the plug where the coil loom connects to the engine loom, and the CAS plug. Need quality connections there. Also look to injector plugs. And the AFM plug while you're at it. Also look to whether your injectors are clean and flowing evenly. Get them out and onto a testbench.
    • Good to know, I feel like I am in for a rollercoaster ride that looks like a sine wave. 
    • You'll fit right in. Acceptance is the first step.
    • Hey folks. I've been lurking and browsing the forum for a while, since I got into my head that I wanted a skyline. Having purchased an overpriced completely stock GTT, (only "mods" it has is HKS pod filter and catback) now that it became legal in the US, it was all glorious and sututu noises here and there. But then I wanted to do things right and went to do basic maintenance. After all the fluids, filters done, I did the spark plugs, that's when the problems started.. First the car started spluttering at around 4.5k RPM. Which I gapped down the new plugs and that solved the sputter there, but the car now always misfires at idle with pops when lifting off and shifting 2nd to 3rd. Similar to the issues in this recent thread. I've been banging my head against the wall, reading the threads here and trying suggestions for a couple months now, so decided to start this one to explain exactly what I tried and what is going on. The symptoms of the issue: Idle and low revs misfiring intermittently. You can hear the exhaust tone change and the shakes on the shifter knob. It happens frequently, but doesn't seem to have a rhythm to it. Pops when backing off throttle. It pops and or burbles almost feels like it spits fire when it pops. (Happens mostly in 3rd gear at around 2k RPM). When under load and after 6k RPM, it also pops when shifting from 2nd to 3rd. There's a ticking noise at around 2k RPM in 2nd gear going downhill, seems unrelated though but I am out of educated and downright dumb guesses. Not noticeable lack of power when putting the car into load. The attempted diagnosis and solutions: Unplugging coils when the car is running This did nothing to change the idling and tone shift for every cylinder. Checking the exhaust headers with thermometer They all are within what I'd say it is margin of error of the laser thermometer New spark plugs Tossed two new sets, copper, iridium and using the old ones, still misfiring, even re gapped to 0.8mm, still same thing. MAF cleaned with the "specific" spray cleaner No changes in the issues what so ever. Brand new loom and r35 coil conversion (was going to add the r35 coils anyway) car runs arguably better, still misfires, but seems like does less frequently. Placebo? Code 21 now being thrown, thanks nissan gods. Removed the CAS to check the shaft for play or anything. CAS seems all fine, nothing that indicates any issue, visually speaking. Things to attempted next: Ordered a new MAF (chinesium from Amazon, to be able to return regardless of result). Fuel with proper gas, maybe it is this California water that they sell as gas that is to blame? Plugin the link ECU and check the info using the built in base map. Go back to BMW and eat my rob bearing breakfast without milky oil mixture.   Do any of you have experienced anything like this or have any suggestion?
×
×
  • Create New...