Jump to content
SAU Community

S2 Stagea Servicing

SABBAi

By SABBAi,
in Four Door Family & Wagoneers

 Share

Recommended Posts

SABBAi Grand Master

SABBAi

Posted
Posted

Hi All,

I've been reading through the parts numbers thread/DIY service thread etc, but there are a few things I can find.

I've found a Dayco timing belt (PART No: KTBA173) but it doesn't list that it fits the RB25DET Neo. It lists RB20DET, RB25DE, RB26DETT. I would assume that it would fit the 25DET also?

Also, how many litres do the auto trans hold? I want to make sure I have enough fluid to cover a flush as well as a fill.

Any idea on where to get rear wheel bearings and wheel studs from in Bris? Right rear wheel bearing is making some unhappy sounds and one of my LH rear wheel studs sheared off.

Cheers

Scott

Link to comment
https://www.sau.com.au/forums/topic/318428-s2-stagea-servicing/
Share on other sites
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Can't help you with the parts as i'm in NZ but you need 12 -14L to do the auto so best bet is to look for a 20L drum of quality synthetic atf and you can use it for the Atessa and power steering as well.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Some stuff i dug out of the DIY thread (parts list):

S2 wheel studs #43222-70T00

OK Series 2 part numbers are:

Water Pump 21010-AA526

Timing Belt 13028-5L327

Tensioner 13070-5L300

Idler 13074-58S00

Nissan rear wheel bearing ass c/w bracket 43210-AA100

Possible cheaper alternative:

New part number for rear wheel bearings to suit s2 auto . CBC Bearings carry these .

Kit NJ246.

To suit, 200sx 7/94-2003

Skyline 6/91-3/93 2.0L

Skyline 6/91-3/93 2.6L 4 stud only

Skyline 8/93 on 2.5L

Skyline 8/93 on 2.6L 4 stud only

Best part is the price $154.00 incl gst. The genuine nissan price was $323.00.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
Thanks Bob, I found that too. Just don't know if CBC Bearings is Aus wide or not.
It would appear so:

http://www.google.co.nz/#hl=en&source=...1aa81ab65bd61af

and the cam belts appear to be all the same: 25, neo, 26

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...