Jump to content
SAU Community

1990 Nissan Skyline Turbo 4 Door Manual

Hawker180
 Share

Recommended Posts

Hawker180 Proficient

Hawker180

Posted
Posted (edited)

For sale:

1990 Nissan R32 4 door - Turbo manual

km's: 12x,xxx (have had it since 70,000 and most is highway km's)

The Car used to be Non-Turbo Auto, but is now Turbo Manual...the conversion was done properly and has been very reliable for the last 10,000kms. Most of the time this is just putted around as to me its just a daily As i have a track 180sx as well.

Car doesnt have HICAS at all, and driveline and brakes, 5 stud hubs are all GTST now and the diff is a stock LSD.

RB20DET

5 stud conversion

R32 GTST Brakes + Brake booster

Turbo LSD

Velour Late model seats and trims

Swapped All side glass out (as it was tinted)

3" Cat back exhaust

Manual conversion kit

th_Hawker180_R32cooler.jpgth_Hawker180_R32engine.jpgth_Hawker180_R32Front.jpgth_Hawker180_R32inside.jpgth_Hawker180_R32inside2.jpgth_Hawker180_R32rear.jpgth_Hawker180_R32Side.jpg

The Car:

1990 Nissan R32 GTS

RB20DET (originally RB20DE)

5 speed Manual (originally Auto)

Engine mods:

Stock RB20DET

Stock Turbo (genuine 55,00kms on turbo when i put it on)

GReddy Return flow Intercooler

K&N Panel filter in stock airbox

Spitfire coil packs

3" Cat back Exhaust

Walbro Fuel Pump (Genuine)

Turbo Radiator

Exedy 5 puk clutch

Electronic:

GReddy Profect Boost Controller (not setup, just using it as a guage at the moment) Boost is bleed with a bleed tap (0.9 bar)

Suspension:

KYB Lowered Struts and springs

5 stud conversion - R32

R32 LSD Auto - (originally single wheeler)

R32 GTR rear swaybar front is stock

Exterior:

Rare 4 door Type M Skirts and bibs

Dark tint all around

Tow bar, great for 6x4/motorbike trailer etc...

Interior:

Velour Late model 4 door seats out and trims (originally grand-pa spec) - these are awesome condition!

Skyline floor mats

GTST steering wheel

Blaze gearknob

The bad:

It has 2 large scratch marks from keys (both before i brought it), one on the bonnet and one down the passanger side.

Rear guards need some paint as i rolled them to suit the wider wheels.

Front bumper has scrapes on it

Car currently has Work Meisters on it, would perfer to sell with stock wheels at a cheaper price but could come with the other wheels for extra of course

Price: $8,500 FIRM with stock wheels

$9,500 FIRM with Work Meisters (Black centre 17x8 +30 and 17x9 +30)

No SWAPS, unless you have a BA Ford Ute/Sedan + money

no RWC, Photos are pretty old, can post up some new ones with the nicer seats/steering wheel as well as the current wheels.

Edited by Hawker180
V28VX37 Veteran

V28VX37

Posted
Posted
The Car used to be Non-Turbo Auto, but is now Turbo Manual...the conversion was done properly and has been very reliable for the last 10,000kms.

Did you use the original RB20DE or drop another RB20DET in there? Is it registered with VicRoads?

Is the car currently registered? If not when did the rego expire?

What do you reckon is required for RWC?

Cheers

Hawker180 Proficient

Hawker180

Posted
  • Author
Posted (edited)

Its is another engine out of a donor skyline I purchased. So a stock RB20DET. New engine numbers and Turbo has properly gone through vicroads as i also did the Brakes etc... It didnt require an engineers certificate.

Still registered (rego expires in a few days, but i will renew it so it will have 12months rego on it)

For RWC im not thinking much, but its hard to day. I reguarly maintain it so i dont expect too much will be needed.

Im going to pull the clutch master off this weekend as it is leaking, so that will be fixed

Edited by Hawker180
Hawker180 Proficient

Hawker180

Posted
  • Author
Posted (edited)

th_P1040438.jpgth_P1040439.jpgth_P1040440.jpgth_P1040441.jpg

th_P1040442.jpgth_P1040443.jpgth_P1040444.jpgth_P1040445.jpg

th_P1040446.jpgth_P1040447.jpgth_P1040448.jpgth_P1040449.jpg

th_P1040450.jpgth_P1040451.jpgth_P1040452.jpgth_P1040453.jpg

th_P1040454.jpgth_P1040455.jpgth_P1040456.jpgth_P1040457.jpg

th_P1040458.jpgth_P1040459.jpgth_P1040460.jpgth_P1040461.jpg

th_P1040462.jpgth_P1040463.jpgth_P1040464.jpgth_P1040465.jpg

th_P1040466.jpg

Some decent photos, The insides of the car hasent been cleaned yet, so its just AS IS!

A few things i forgot: Brand new battery, Timing belt and water pump done at 117,000kms, clutch only 10,000kms old (Exedy 5 puk)

Edited by Hawker180
  • 2 weeks later...
  • 2 months later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...