Jump to content
SAU Community

Recommended Posts

Hi,

My bro just got his new line and we were intrested to see what the turbo looked like to compare to other bros turbo.

and we noticed that the fins look different and are bent and chiped ?

is this a problem ? do we need a new turbo ?

their doesnt seem to to be and problem when driving, all though it sounds different when it spools up you can hardely hear it, it doesnt make the whistling sounds like the pod but its a different sounds ?

Thanks,

by the way its on a 95' gtst

(i'll post pics later tonight)

Link to comment
https://www.sau.com.au/forums/topic/31865-damaged-turbo-wheel-r33-gtst/
Share on other sites

Well if you go two turbos off the same series motor.

then you can bet your dollar it's a bit damaged.

chipped is not all that good.

Fins can have a 'bent' look. it might just be the wheel.

I dunno what the differences are between the two though... series I vs II.

but i think there was something a tad different.

either way for a new one you only looking at $400

hi

I think I might be having a problem with my turbo too...

It looks ok the last time I checked it..

but at higher speeds.. about 200km/h + there's a really loud shhhhhhhhhhh sound... quite unnatural...

not sure whether something's wrong with the turbo or the blow off valve...

I'm running on standard turbos and turbosmart BOV..

anyone experienced this before?

thanks

That turbo has ingested something, but if it still goes, then keep using it, unless you really want to upgrade. These turbos are generally, not very servicable or rebiuldable. But they are quite tuff. It could keep working fine for years to come. Look at it this way, you only found the damage, coz you looked....you didnt hear any strange noises or see oil or anything.

You can if you want, buy a new comp wheel and get it fitted and balanced, but Personally I woudlnt bother, the time and money isnt worth the problem if the wheel fails. I doubt you would notice the drop in power at all.

I have been playing (that should read, trying to fix:P) a couple of rb25det turbos, and have found the following info....

If you break the seal plate, you can't get a new one (oh no!) If you own a lathe, you can make a new one (doing that now actually)

The turbine is not able to be serperated from the shaft, and is balanced as a single unit

The comp wheel is balance as a single unit, and therefore, you can generally swap wheels with not too much hassle (if you dont balance them, you will get a shorter turbo life, but generally, you will get away with it)

IF you pull apart totally the bearings, (they are not captive bearings) the balls will fall out and roll across the floor, into the drain, cracks in the concrete etc etc, bye bye turbo....

If you can feel shaft play sideways or end ways, the bearings are worn, but if your lucky, you can still have some more room to tap in the centre peice of the comp wheel side bearing (under that damn seal plate im afraid, hard to take them out without breaking them) and get rid of that play, and get another 100 000 kays out of a unit.

Worn bearings and side play and end play in the shaft leads to misalignment of the seals, which of course leads to oil leaks, smoke, etc....

by the way, I picked up a second hand turbo for $200 on the weekend and fitted it to my twin turbo rb25dett VL and it fixed my problem.

So as you can see, spending money at a turbo shop rebiulding a stock rb25det turbo is not a financially rewarding thing to do. Its better to just source a second hand one.

I had two good turbos, untill one started leaking oil into the air intake. Upon trying to fix that turbo, i broke the seal plate. Bought a buggered turbo for $70 and broke the seal plate in that trying to get it out too! :P (DOH)

Bought another good turbo for $200 and fitted it and no worries.

Now im making two new seal plates, using two new o rings, and setting up the bearings in those two turbos again, to see if i can get those turbos operational again. If not, ill turf them:P

black smoke is fuel not oil.

why should it boost higher than standard boost? you got a bleed valve hooked up?

If you have and its refusing to boost very high, it could be any number of alot of other things. I've never seen a turbo that is in such a state that it wont boost higher than standard boost, unless its really stuffed (turbine hitting houseing, seized bearings, etc)

They seem to either work fine, or dont.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...