Jump to content
SAU Community

Coilpack Question. Nissan Interchangeability?

Paradis v.1

By Paradis v.1,
in Engines & Forced Induction

 Share

Recommended Posts

Paradis v.1 Enthusiast

Paradis v.1

Posted
Posted

It's my understanding that SR20s and RB20s used the same coilpacks (sauf the # needed of course).

Anyone confirm this? I've got Rb20 Splitfires i want to use on an SR, and just want to be sure. I've heard both yes and no to this question.

thanks.

Paradis v.1 Enthusiast

Paradis v.1

Posted
  • Author
Posted
what sr20 is it, becoz some ran a dizzy, even then youd wanna be 200% sure itl work, coz u could burn out the transistor pack and the ecu if your wrong.

Well it doesn't really matter what SR it is (its Crower 2.2), the splitfire coilpacks are good for all 32s-33s, and same with the SR packs s13s and up.

Are these the same Coilpacks though. It would seem so, but i want to know if anyone's sure or not

Paradis v.1 Enthusiast

Paradis v.1

Posted
  • Author
Posted
as long as they aren't the 'Series 2' kind with the igniter built in (which they wouldn't be if they're for an RB20), they should be fine

Series 2 hey? what application would that be? Splitfires for the RB were good for all Rb20, 25, 26 etc, they were a one model fits all. Same with SR ones, CA-SR, 13, 14 etc

If i was to buy OEM coilpacks for my SR20, are the same ones RB20s use?

Paradis v.1 Enthusiast

Paradis v.1

Posted
  • Author
Posted
as used on RB25's without the igniter module

if your SR20 has an igniter module, then it'll use the same coils as an RB20

Ya thats what i figured, but i wanted to double check,

I appreciate the prompt replies though, :merli:

STATUS Grand Master

STATUS

Posted
Posted
It's my understanding that SR20s and RB20s used the same coilpacks (sauf the # needed of course).

Anyone confirm this? I've got Rb20 Splitfires i want to use on an SR, and just want to be sure. I've heard both yes and no to this question.

thanks.

no chance.

mad082 Grand Master

mad082

Posted
Posted

from memory the sr20 coils are much longer than the rb ones, so as status said, i don't think they are going to come close to fitting. i think they will be about an inch too short. all the RB motor ones are short stubby little things.

jjskyline79 Community Regular

jjskyline79

Posted
Posted
Series 2 hey? what application would that be? Splitfires for the RB were good for all Rb20, 25, 26 etc, they were a one model fits all. Same with SR ones, CA-SR, 13, 14 etc

If i was to buy OEM coilpacks for my SR20, are the same ones RB20s use?

Think your find they were'nt mate

They are different for spec one to spec two engines

This is ALL the spec two coil packs will fit and years

DSCF1935.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...