Jump to content
SAU Community

Recommended Posts

I assume by "it wont unlock either" you mean that it is locked right now...

that would be why it doesn't open, so the question is why is the door stuck locked?

Have you tried both using a key and the latch on the inside of the door?

either way, you may have to attempt to take off the door trim and have a look at the locking mechanism, something may be caught in there or it may have rusted/ jammed for some other reason.

but i would say have a look and go from there.

(edit for spelling)

Edited by tiberis

sure is locked now have tried key and inside latch but no go.

but using the key and the latch it will only unlock the the latch (part you can see on the door trim) halfway.

any help on how to get the interior door trim off with breaking it with the door closed ??

also has anyone else had this happen to them ? how did you fix it ?

i dont think u can take off the trim while the door is closed? coz the three screws to remove the door trim are between the bottom of the interior and the door. but not 100% sure...

i also had this problem with mine but i put a little force and shook the key while turnin and it opened. but i dont think its the same prob as urs

Yeah i know about the three little screws down the bottom.

Any more help would be great.

Havent done much execpt pry the door trim away at the top enough to see in.

It doesnt seem to unlock properly by the looks of it so what do i do ?

how bout you remove the thing that surrounds the door opener inside? once its out you might have a little small space too put ur finger and do something lol

you just have to remove a screw i think in the middle and then unclip the surround carefully

  • 4 weeks later...

were you able to get the door trim off at all?

was thinking that you may be able to do it if you take out the front seat. would be a lot of effort, but i think it's coming to the point of trying all options. taking the seat out should let you get to the screws at the bottom, and you mentioned before that you were able to get the top part unhooked. just don't forget the couple of screws through the centre of the door in the arm rest thing.

worst case, you may need to damage your door trim to get it off.. but a door trim costs less than a door if it comes to it.

This happened to mine not 3 days ago. Although I could open my door so no probs.

Start by pulling out the door handle/lock surround on the inside. No screws, just a few little clips. This will allow you to grab the steel rod with a pair of pliers/vice grips and will give you more pulling power without the risk of breaking the plastic lock switch or door handle.

Mine was simply a small piece of plastic jammed into place preventing the mechanism from opening. Don't know where it came from but I removed it and all was well so f@#k it.

Anyways try to unlock and open the door this way first. If it is just something jammed in place, the extra force may budge it just enough, as the plastic handles will not allow as much force to be applied.

FORCE: Sometimes it's the only way. Other times it just seems like a good idea at the time, and can be fun when frustrated.

I'M trying to think without going and looking but cant you wind the window down and use a coat hanger or something to get at the lock mecanism?

Or If the inside lock tab thingy is only opening halfway then something is obviously blocking it, i would try to open and close the inside lock tab fast and slow and hit the door firmly but not to hard to see if it unlocks.

Worth a try. :kiss:

  • 2 weeks later...

still no go and yes i have got the door trim off had no choice but to break it off tho i still can not get the door open :D tho at this point its the least of my worries now as my motor blew 5 days ago :( but i would still like to get it open any more help would be greatly appreciated

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...