Jump to content
SAU Community

R34gtt Neo Engine Problems

R34-2NV
 Share

Recommended Posts

R34-2NV Enthusiast

R34-2NV

Posted
Posted

has anyone ever heard of a fairly stock neo turbo engine needing a rebuild a few months after a new clutch being installed.

I only a few months ago put a nismo coppermix clutch into my skyline gtt neo and a few weeks after the clutch was installed i could hear weird clonking and clicking noises whenever i applied the clutch.

a couple months later and the mechanic who installed it is telling me that my engine bearings are gone and my engine would need a rebuild due to the stress caused on it from the spun bearings.

before the clutch was installed there was not one odd sound out of the engine or gearbox and the car always drove like a dream.

I always service it with good synthetic oil quite regularly and check to make sure everything is good.

In my last service which was a couple weeks after the new clutch was installed i found little metal pieces in the oil which i have never seen before (and I always check the oil for anything unusual).

Can a clutch not installed right cause this to the engine? or could the oil pump have been clogged from these little metal pieces that would have come from the clutch, as when the clutch was taken out to be inspected it was heavily worn and only after a couple of months.

I never take it to the track or thrash it. its a weekend car and i baby it all the time.

I need help with this because im finding it hard to trust my mechanic anymore especially considering that i get all mu tuning done there and it would be reasonable to say that if then engine was on its way out due to a fault he would pick it up on a dyno check which i have done a few times.

Link to comment
https://www.sau.com.au/forums/topic/319964-r34gtt-neo-engine-problems/
Share on other sites
mad082 Grand Master

mad082

Posted
Posted

more than likely the clutch being installed has nothing to do with the engine letting go.

the clutch itself may have indirectly have something to do with it, but again, it would have only brought to light a problem that already existed. if you went a heavier duty clutch and then even just a few times did a few silly things then the extra stress from the clutch grapping much better could've been enough to be the final nail in the coffin for the engine. or it could have nothing to do with it and it is all just coincidence.

R34-2NV Enthusiast

R34-2NV

Posted
  • Author
Posted

yeh fair enough, i think the oil pump may have had something to do with it though, i probably should have upgraded it after the clutch was put in. I honestly dont do anything stupid with this car, the odd hit here and there but im not really a burnout person (not in this car anyway). either way new engine must be put in because rebuild just cost too much these days. Labour being the most expensive part!!!

more than likely the clutch being installed has nothing to do with the engine letting go.

the clutch itself may have indirectly have something to do with it, but again, it would have only brought to light a problem that already existed. if you went a heavier duty clutch and then even just a few times did a few silly things then the extra stress from the clutch grapping much better could've been enough to be the final nail in the coffin for the engine. or it could have nothing to do with it and it is all just coincidence.

QUICKY Community Regular

QUICKY

Posted
Posted

mate ide get another mechanic to have a look at it.

you said you hear the clunking noises when u apply the clutch which leads me to believe that it just may be the pucks/plates in the clutch rattling.

get another opinion and keep us posted

good luck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
    • soviet_merlin
      R32 GTST - 600KW+ RB28/CD009 Build

      By soviet_merlin · Posted

      What sold me on Trailer Park Boys is this scene: Great stuff, just stay clear from the new Netflix production.
×
×
  • Create New...