Jump to content
SAU Community

Recommended Posts

from memory i dont think that they have different holes in the boot......the base of the wing is same for both models me thinks....same goes for the GTR wing too....dont quote me on it but i dont think that the holes are different at all

i normally see a S2 wing on S1's your going in the opposite direction....

Ok so I ended up buying a series 2 boot lid and wing to bolt on (hinges too).

I bolted it on and the boot lid would not latch shut. After some investigation I noticed the latch bit that bolts onto the lid is a different shape. I bolted the series 1 latch onto the series 2 lid and it now latches shut.

The only problem is that it now sits about 20mm too high at the rear. I found that I can adjust the latch on the car side by loosening 2x bolts and sliding it down.

I think this helped a little but not enough..

Does anyone know if there is any further adjustments that can be done?? Or could the hinges be different etc??

HELP!!!

  • 4 months later...

Just changed my s1 wing to a s2 and found that the pointed ends of the s2 wing are longer than the s1 one by an inch or so. Maybe the s2 lid is slightly longer than the s1 one, thus not allowing you to fit in flush on your s1. Just a guess through inspiration from the wing as I could be wrong.

Ok so I ended up buying a series 2 boot lid and wing to bolt on (hinges too).

I bolted it on and the boot lid would not latch shut. After some investigation I noticed the latch bit that bolts onto the lid is a different shape. I bolted the series 1 latch onto the series 2 lid and it now latches shut.

The only problem is that it now sits about 20mm too high at the rear. I found that I can adjust the latch on the car side by loosening 2x bolts and sliding it down.

I think this helped a little but not enough..

Does anyone know if there is any further adjustments that can be done?? Or could the hinges be different etc??

HELP!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...