Jump to content
SAU Community

Recommended Posts

Nissan Skyline R32 GTR 1993 N1 Turbos

27,000km independently confirmed.

The car has the original N1 turbos that are larger and don’t have the typical ceramic turbines that frequently break under improved boost, rather it has steel turbines designed for increased boost.

The car has only ever been owned by two people. I’m over 50 and the only owner since imported, it was previously owned by a 60 year old school teacher in Japan. This means it has never been owned by a young person or miss been treated. I have never increased the boost and believe it was never done in Japan either.

The car was dyno tested when it first arrived in the country and produced 196kW at all four wheels on the standard 7.5psi. This figure is easily over 200kW if tested at the rear wheels. Amounts to around 290kW at the flywheel.

Stunning White.

5 speed manual.

Looks good inside and out. Tiny bump in hood.

This car hasn’t been modified since imported and has hardly been driven.

OS Giken twin plate clutch.

HKS Dump pipes.

HKS Front pipes.

HKS Hi-Power 95mm (3.75inch) hi-flow exhaust.

HKS Hi-Power 120mm (4.72 inch) muffler.

16inch rims.

HKS Pod filters.

Very rare rear lip.

Steering wheel.

CD player.

Stereo system.

Just been taken to two mechanics for check and service before sale.

Peders - Suspension checked, plus:

· Wheel alignment.

· Front rod bush replaced.

Mechanics – Service and check, plus:

· New battery

· New platinum plugs

· Tuned engine bay.

Always garaged and only driven occasionally on weekends.

The car is being sold due to underuse.

I only want to discuss further with serious buyers.

I don’t want to trade as I have other cars already.

Located in South Australia, Western suburbs.

If you reply via online it may take a short time for me to answer as I’m currently rather busy.

Price: $17,500

Contact Person: Samuel 0433 031 312

post-40400-1274768858_thumb.jpg

post-40400-1274768907_thumb.jpg

post-40400-1274768922_thumb.jpg

post-40400-1274768955_thumb.jpg

what does "independently confirmed" mean?

i don't want to take anything away from your sale but i'd bet money on it not being genuine.....

Let the guy sell his car mate, if someone is keen on buying it they can have it checked out for themselves.

Good luck with sale Samuel

No worries guys.

The car and the log books were checked by two Japanese mechanics who could read the log books. They both agreed that the log books were genuine and the odometer was correct.

Thanks

No worries guys.

The car and the log books were checked by two Japanese mechanics who could read the log books. They both agreed that the log books were genuine and the odometer was correct.

Thanks

hey mate, could you pm me an email address so that I can get in contact with you?

can't PM yet because of post count :(

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity.
    • 100% the factory sender is tapered, that is how it seals (well, that and teflon paste or tape)
    • Thanks folks - I've saved a few links and I'll have to think of potential cable/adapters/buying fittings. First step will be seeing if I can turn the curren abortion of a port into something usable, then get all BSPT'y on it. I did attempt to look at the OEM sender male end to see if it IS tapered because as mentioned you should be able to tell by looking at it... well, I don't know if I can. If I had to guess it looks like *maybe* 0.25 of a mm skinnier at the bottom of the thread compared to where the thread starts. So if it is tapered it's pretty slight - Or all the examples of BSPT vs BSPP are exaggerated for effect in their taper size.
    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
×
×
  • Create New...