Jump to content
SAU Community

Recommended Posts

Hi guys,

I've been putting up with the issue of water running into my headlights (Indicator part) and staying there untill evaporated.

Im getting sick of it i have tried taking it off and buying proper headlight sealent but it hasnt helped. Its doing it again.

I've noticed my mates skyline (R33) has the same problem and a few ive checked out after being washed have the same problem.

After last nights non-stop raining ive walked out to see my whole indicator filled with water.

Has anyone had past experience with this? Any suggestions?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/322161-r33-rear-taillights-leaking/
Share on other sites

Hi guys,

I've been putting up with the issue of water running into my headlights (Indicator part) and staying there untill evaporated.

Im getting sick of it i have tried taking it off and buying proper headlight sealent but it hasnt helped. Its doing it again.

I've noticed my mates skyline (R33) has the same problem and a few ive checked out after being washed have the same problem.

After last nights non-stop raining ive walked out to see my whole indicator filled with water.

Has anyone had past experience with this? Any suggestions?

Cheers

sorry guys i mean my taillights..

I remember reading somewhere on the forum that a dodgy boot seal can cause water to leak around your tail lights. Is your boot seal in decent condition?

yeehh that was a possibility in my mind.. but i went out to confirm it and my boot seals in perfect condition!! no cracks or wear and tear..

Generally a lot of the factory seals perish over time, and quite badly when your car lands in a country with a complete different climate. I had this problem with my old s1 33 (never got around to fixing it though), and you do see this on a lot of other 33s.

Solution i'm leaning towards; pull apart tail light completely, remove all old junk sealant, give all bits a very good clean, and then re-seal everything with reccommended headlight adhesive.

Generally a lot of the factory seals perish over time, and quite badly when your car lands in a country with a complete different climate. I had this problem with my old s1 33 (never got around to fixing it though), and you do see this on a lot of other 33s.

Solution i'm leaning towards; pull apart tail light completely, remove all old junk sealant, give all bits a very good clean, and then re-seal everything with reccommended headlight adhesive.

cheers for the repliess

ive just decided to take both of your ideas.. Im going to drill a small hole in the lowest point of the indicator and then im going to clean it up and buy more of the taillight sealent and try to do it again :(

cheers guys i will let you know how it comes out

test the seal before you drill, if you leave a hole im pretty sure it can build up condensation inside, and you still get that stupid beady-water look in the morning.

when your talking about the seal do you mean the seal around the taillight? if so its only got the adhesive no seals? ive also noticed my taillights somehow cracked on the bottom indicator part..

I might seal that part up as well

I will let you know how it comes along

cheers

i had this problem too. resealed the taillights onto the body. made no difference.

so i removed my bumper, and drilled a small hole under each blinker so water will run straight through. havent had a problem since.

i think the real problem is the glue on the tail light lenses inside the tail light assembly has failed and the water runs in through the lenses, instead of running around them and draining as it should.

so i imagine you would have to pull each light apart and reseal it internally.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...