Jump to content
SAU Community

Recommended Posts

hi all

i did a search before but forgive me if this has already been asked.

i currently have sumitomo HTR ZII all round on my car

they are forward directional, but also inside/outside specific

dont want to get into a tyre debate here lol

i have a bit of inside camber wear going on...so what i need to know is

can the tyres be flipped from side to side, putting the *outside* on the inside...to even up the camber wear?

obviously the tyre has been designed that way for a reason but i was just wondering how much difference it actually makes.

thanks

Link to comment
https://www.sau.com.au/forums/topic/322654-directional-and-side-specific-tyres/
Share on other sites

got the same tyre on my car.

i flipped the rears didnt notice any diffrence but in the wet they might not be as good?

cheers mark

i might just give it a go, its either that or get new ones so might as well.

I run tyres backwards on the rim often in the race car, in the dry, there is no noticeable loss of performance

However I think you are mad to do the same on a street tyre. There are 2 key things that are different - as Mark said the wet performance suffers because the tyre is not designed to pump water in the direction you are running it. Also it is possible the internal construction may have a problem running backwards eg steel belts loosening.

If it was safe to run these tyres backwards the manufacturer would say so - they only use assymetric or directional design when they have to to meet a certain performance goal.

On a related topic....what is your wheel alignment (camber and toe, front and rear)? If it is out you are better to address the problem than throw new tyres at it.

Why not swap the tyres onto the opposite rim, so that the tyre at least continues to rotate in the same direction - ie, take the tyre off the LH rim, and mount it on the RH rim, with the "outside" now "inside". Only the inside / outside property would be compromised.

mark maybe the zIII are different because mine are definitely direction as well...

im aware its not an ideal but just trying to get a bit more life out of the tyres before i have to replace them

also am aware i should really address the cause of the camber wear, im assuming adjustable camber arms will enable this to be resolved?

thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...