Jump to content
SAU Community

Recommended Posts

Ok guys im looking into to turning my skyline into a a full drag set up so im looking at selling me twin turbo set up thats on my r33 gtst ,its a twin 3037 with .8 or .6 rear housing ,which ever you would like ,it will come with everthing you will need ,as im looking at going to somthing like a gt4508 ,

so it will come with 2 gt 3037 with .6 or .8 housing ,mainfolds dump pipes .a full twin 3 inch exhurst 2 air cleaners and intake pipes ,a twin entry 105 mm thick blitz intercooler ,2 turbo blankets ,also twin screamer pipes with 2 tail 38mm gates all the water lines and and oil return lines ,allm nuts and bolts ,

all the goods are still on the car so if you would like pix thats no probs ,the car is running 488.9 rwkw with this set up on it with a man and on pump fuel with 23 psi ,the turbo have had very little use only run in time on the motor and 8 passes down the strip.

all parts will be sent from Townsville Qld 4818

and im looking round $5000, ono

if anyone would like pix pm me a e mail address and e mail some pix .

cheers

Link to comment
https://www.sau.com.au/forums/topic/323651-twin-turbo-set-up/
Share on other sites

Ok guys im looking into to turning my skyline into a a full drag set up so im looking at selling me twin turbo set up thats on my r33 gtst ,its a twin 3037 with .8 or .6 rear housing ,which ever you would like ,it will come with everthing you will need ,as im looking at going to somthing like a gt4508 ,

so it will come with 2 gt 3037 with .6 or .8 housing ,mainfolds dump pipes .a full twin 3 inch exhurst 2 air cleaners and intake pipes ,a twin entry 105 mm thick blitz intercooler ,2 turbo blankets ,also twin screamer pipes with 2 tail 38mm gates all the water lines and and oil return lines ,allm nuts and bolts ,

all the goods are still on the car so if you would like pix thats no probs ,the car is running 488.9 rwkw with this set up on it with a man and on pump fuel with 23 psi ,the turbo have had very little use only run in time on the motor and 8 passes down the strip.

all parts will be sent from Townsville Qld 4818

and im looking round $5000, ono

if anyone would like pix pm me a e mail address and e mail some pix .

cheers

Hi,

I am looking for a 100/105mm twin entries intercooler for cercuit work.

I have got a near new Trust 130mm FMIC taken off a GTR33 with T88-34D rated at 900hp 44mm HKS waste gate manifold front pipe etc. for compliance and rego. In storage, no shaft play at all. ( power run dyno at 355kw all 4 untouched from the dock, should be a lot more)

I also have another T88-38GK rated at1200hp with 48mm gate and all the set up dyno at 455kw at all 4 22psi on pump fuel. Engine being refreshed ATM.

Building a time attack GTR33 now. will be using -5 and HKS 2530 for the respond.

If you don't mind to send me pic of your set up, mainly the Blitz cooler. ( prefer ARC twin entries 100mm if any body got one to sell or swap) will consider your Blitz if you end up seperating

email [email protected]

Alex 0433 878905

Mordialloc Vic 3195

www.jds-auto-imports.com

You change your mind more than I do. lol

Just lean on the boost a little and tune it for E85.

What times have you run with this setup so far...?

Goodluck with the sale

LOL ive only ran 10.4 @ 136 mph on pump fuel ,i would love to go e85 but its to hard to get to townsville Qld ,so im just going to use roo 16 ,but im still not sure yet ,if i can sell the whole set up i will go to single cause i was thinking about trying the water to air cooler as well .

have you got your car running yet ?

Hi,

I am looking for a 100/105mm twin entries intercooler for cercuit work.

I have got a near new Trust 130mm FMIC taken off a GTR33 with T88-34D rated at 900hp 44mm HKS waste gate manifold front pipe etc. for compliance and rego. In storage, no shaft play at all. ( power run dyno at 355kw all 4 untouched from the dock, should be a lot more)

I also have another T88-38GK rated at1200hp with 48mm gate and all the set up dyno at 455kw at all 4 22psi on pump fuel. Engine being refreshed ATM.

Building a time attack GTR33 now. will be using -5 and HKS 2530 for the respond.

If you don't mind to send me pic of your set up, mainly the Blitz cooler. ( prefer ARC twin entries 100mm if any body got one to sell or swap) will consider your Blitz if you end up seperating

email [email protected]

Alex 0433 878905

Mordialloc Vic 3195

www.jds-auto-imports.com

post-51182-1275820741_thumb.jpg

Hi,

I am looking for a 100/105mm twin entries intercooler for cercuit work.

I have got a near new Trust 130mm FMIC taken off a GTR33 with T88-34D rated at 900hp 44mm HKS waste gate manifold front pipe etc. for compliance and rego. In storage, no shaft play at all. ( power run dyno at 355kw all 4 untouched from the dock, should be a lot more)

I also have another T88-38GK rated at1200hp with 48mm gate and all the set up dyno at 455kw at all 4 22psi on pump fuel. Engine being refreshed ATM.

Building a time attack GTR33 now. will be using -5 and HKS 2530 for the respond.

If you don't mind to send me pic of your set up, mainly the Blitz cooler. ( prefer ARC twin entries 100mm if any body got one to sell or swap) will consider your Blitz if you end up seperating

email [email protected]

Alex 0433 878905

Mordialloc Vic 3195

www.jds-auto-imports.com

Mate ill see if i can pull the front bar off and take a pix for you ..if you like

You change your mind more than I do. lol

Just lean on the boost a little and tune it for E85.

What times have you run with this setup so far...?

Goodluck with the sale

LOL ive only ran 10.4 @ 136 mph on pump fuel ,i would love to go e85 but its to hard to get to townsville Qld ,so im just going to use roo 16 ,but im still not sure yet ,if i can sell the whole set up i will go to single cause i was thinking about trying the water to air cooler as well .

have you got your car running yet ?

Had it running and tuned but didnt make it to the track. Is in parts again but am building a house now so the toys have to wait a few more months.

Could you get a few 205 drums of E85 sent up to townsville...?

You change your mind more than I do. lol

Just lean on the boost a little and tune it for E85.

What times have you run with this setup so far...?

Goodluck with the sale

LOL ive only ran 10.4 @ 136 mph on pump fuel ,i would love to go e85 but its to hard to get to townsville Qld ,so im just going to use roo 16 ,but im still not sure yet ,if i can sell the whole set up i will go to single cause i was thinking about trying the water to air cooler as well .

have you got your car running yet ?

Had it running and tuned but didnt make it to the track. Is in parts again but am building a house now so the toys have to wait a few more months.

Could you get a few 205 drums of E85 sent up to townsville...?

yeah but cause its dangerous good its ex to ship thats all ..and i didnt no you could buy it in 205 ltr

Couldn't reply to your pm, I haven't been enough of a post whore yet. I'm chasing sponsors at the moment, it all depends on which one bites first. That said, I have a better chance than most in this area, though I won't rant on about why. It's a bit is a "how long is a piece of string?" question, could be this week, could be a few weeks away. If you don't want to wait then I understand. I'm sure I'm not the only one looking for this sort of set-up.

Hi,

I am looking for a 100/105mm twin entries intercooler for cercuit work.

I have got a near new Trust 130mm FMIC taken off a GTR33 with T88-34D rated at 900hp 44mm HKS waste gate manifold front pipe etc. for compliance and rego. In storage, no shaft play at all. ( power run dyno at 355kw all 4 untouched from the dock, should be a lot more)

I also have another T88-38GK rated at1200hp with 48mm gate and all the set up dyno at 455kw at all 4 22psi on pump fuel. Engine being refreshed ATM.

Building a time attack GTR33 now. will be using -5 and HKS 2530 for the respond.

If you don't mind to send me pic of your set up, mainly the Blitz cooler. ( prefer ARC twin entries 100mm if any body got one to sell or swap) will consider your Blitz if you end up seperating

email [email protected]

Alex 0433 878905

Mordialloc Vic 3195

www.jds-auto-imports.com

Hi, I have got a PWR water to air cooler,with pump and seperate radiator,etc which I have not even tried yet.It is here for my S15 but it has a good ARC already and will be re tuned to E85 in RE Custom tomorrow then will track test the whole set up in Sandown and Phillip Island.If we end up getting around 300kw at wheel, I don't need to use the PWR.

  • 2 weeks later...
how hard would this be to adapt to a rb26

The water to air heat exchance tube can be mounted anywhere handy to feed cooled air to intake and the little water radiator and electric pump can be mounted like a oil cooler in front of normal radiator.

May put this device into a Hiace turbo diesel ( no room for normal air to air cooler with piping) to see what gain it achieves.

Would like to swap an ARC twin entry for curcuit work.

post-50742-1277028627_thumb.jpg

post-50742-1277028637_thumb.jpg

The water to air heat exchance tube can be mounted anywhere handy to feed cooled air to intake and the little water radiator and electric pump can be mounted like a oil cooler in front of normal radiator.

May put this device into a Hiace turbo diesel ( no room for normal air to air cooler with piping) to see what gain it achieves.

Would like to swap an ARC twin entry for curcuit work.

the water to air i was looking at doing was a pwr or a plazman .and just run a ice box instead with water and a pump instead of the radiator ,so i can keep temps down while at the drag strip.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...