Jump to content
SAU Community

What Makes A Brembo Caliper "f50" Or "f40"?

_Wing_
 Share

Recommended Posts

T04GTR Grand Master

T04GTR

Posted
Posted
This is an F40 calliper. To the best of my knowledge it looks no different from an F50 - piston areas aside. It does look and is different from the Brembo's found on the R33's etc & from the current range of Brembo callipers.

Also to the best of my knowledge there is no difference between an F40 & an F50 pad (Which in turn is the same as a Brembo equipped BA Falcon, oddly enough).

Lastly I am not aware of there being any difference in the rotor sizes that these callipers can accomodate ie an F40 can go on a 324 rotor (like mine) a 343 rotor or a 355 rotor. As can an F50.

those are f40. f50 doesnt wrap around the disk as much.

ps. you can also use a "wide face" 355mm disc used by holden i think, in a 2 piece disc hat combo but using a custon hat.and use evo/sti pads for a much wider pad area

  • 10 months later...
Havoc1 Newbie

Havoc1

Posted
Posted (edited)

Heres my new puppies.

On the way from Japan at the moment, should be here next month.

Brembo 6pot with a 380mm rotor. Any idea what they are off?

Old thread but.... With some small exceptions in the bridge and brake hose attachment area, those calipers look a heck of a lot like the early version 6 pots used on some AMG Mercedes.

$4.5K? Wow, everything is spendy down there. I realize that's for calipers/rotors/mounting brackets, etc., but still! I bought a pair of the same calipers in the US for $730 in 2009, and they were practically brand new.

AMG Mercedes... ignore the OEM mounting bracket.

DSC04267.jpg

DSC04268.jpg

DSC04266.jpg

DSC04270.jpg

DSC04269.jpg

Edited by Havoc1
  • 4 weeks later...
gslrallysport Experienced

gslrallysport

Posted
Posted

all well and good, but what about pad and disc replacement costs? i prefer to stick with a nascar type pad wick can be had new dor less than 200 bucks, also 25-30mm thick...

We've got about 8 different options on pads for that Ford/Merc 6 piston Brembo, it's quite a common caliper.

With regards to Nascar pads, alot of the teams are switching to Project Mu now because, although more expensive than the current crop of US made stuff, they last ALOT longer, and the Nascar pads are distributed worldwide from PMU here in Australia, not Japan, so depending on what you're after, you'll be able to buy the PMu Nascar pads here cheaper than what you'll be able to if you buy a set having done a round trip around the globe. Yes, they'll be more expensive, but as most categories are finding now (particularly the V8's and Porsche Cup locally) the PMu gear lasts alot longer than most other big name brand stuff, so pays for itself pretty quickly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...