Jump to content
SAU Community

Recommended Posts

Hi there Guys,

It's been a while since i have posted a question and i have done some searching through the forums but i can't seem to find what i'm looking for.

Problem -

1995 Series 1.5 Skyline RB25DET

* Issues started with low idle - and engine stalling when cold (By the way it's an automatic) Engine would stall if any load was put on it.

* Investigated timing and all timing marks line up for 15Deg

* I've had fun by doing the following - re-Gapped sparkplugs; Got a 2nd hand CAS; Got a 2nd hand AFM; Brought new plugs

I've just been playing with the car today and managed to get it firing by itself but i had to hold my hand over the AFM to restrict the flow Engine was able to idle for 3-5secs before stalling again - I repeated the process and when firing took my hand off and died -

I'm thinking in my mind the following -=-

Either I have a break in the pipe work (Intake) but when i had my hand over the AFM the pipe was sucking in and i couldn't hear any other air. Or the AFM is cactus.

Does anyone have any other thoughts -

Regards,

Ashley Neal.

Link to comment
https://www.sau.com.au/forums/topic/324689-r33-rb25det-15-dramas/
Share on other sites

Check trouble codes then

check fuel pressure

The ECU did show me Code 55 - Everything OK -

The Fuel Pump is working - I disconnected the Feeder pipe and put into a bottle plenty of fuel went into the bottle - Is there a spec on how much presure should be there?

whats it like when its warm?

is it on a stock ecu?

if its always idling very low and is on a stock ecu, perhaps try to adjust the idle up a touch. theres also a mixture screw on the back of the ecu that you could fatten up a touch, that makes them run a little easier when their cold. But if you add fuel on base idle you will also want to up the idle screw.

GL

whats it like when its warm?

is it on a stock ecu?

if its always idling very low and is on a stock ecu, perhaps try to adjust the idle up a touch. theres also a mixture screw on the back of the ecu that you could fatten up a touch, that makes them run a little easier when their cold. But if you add fuel on base idle you will also want to up the idle screw.

GL

Hi mate,

The car seems to be racing when warm - sitting just shy of 1000rpm - when spec say's 650+/- has a slight sputter every now and again.

The ECU is a completely sealed unit with no trimpod for adjustment. I also checked for Dry-Solder in the AFM - and everything checks out there = ECU still giving Codee 55 = All Ok.

Edited by Nissan Maaaart
id go for fuel pump.

They can throw up an array of symptoms but seem ok with prelim testing like you did.

Otherwise vacuum leak...

Thanks mate, I've checked all the Intake piping and there is no apparent air leaks - does anyone know what type of presure should be coming from the rail --

I also did some further testing and with doing the following - blocking the Intake - and allowing a small vaccum of air into the AFM - the car would start with timing retarded - engine would fire on it's own for a moment - but if i removed my hand or made the vaccum less the engine would stall --

The suction from cranking felt quiet faint - can anyone comment on this?

Thanks.

did you look at all the piping cooler etc? my freind had a problem with his for 3 weeks before finding a pin hole in the intercooler.

try changing the fuel filter as well my turbo pulsar wouldnt run and idle and it was a blocked fuel filter but it still primed etc

+1 for fuel filter...im assuming you've checked your air filter..

My mates car wasnt starting, and racing at idle, i blew out the air filter with a compressor and it ran great for another couple of days..cheap prick wouldnt spend 20$ on a new one

Righto - Still Not anywhere -

I've replaced - all clamps, enusres tight- checked Cooler for leaks - new fuel filter -

And still no go - does anyone know how much New AFM's are and where to get them -- as I got a price from a crowd and it seemed a little steep at 780$ex out of Melb.

Or does anyone on the Northside of Bris have a 3 pin (Pink Lable) AFM that is known good that i could try?

Thanks.

Try a diffrent AFM had a simular problem on a mates car, Go to a wreckers or something and you might be able to test it, also AAC valve is clean? check that as well. Do you also have a BOV? or is it stock standard?

Edited by geraus

just unplug the AFM and see if it idles

the engine will run with no AFM and should idle OK, but it wont drive very well and will rev cap at 2500RPM

if the AFM is the culprit when you unplug it, it should run to normal idle

if the AFM is NOT the culprit when you unplug it, the same problem will be present and it will stall

just unplug the AFM and see if it idles

the engine will run with no AFM and should idle OK, but it wont drive very well and will rev cap at 2500RPM

if the AFM is the culprit when you unplug it, it should run to normal idle

if the AFM is NOT the culprit when you unplug it, the same problem will be present and it will stall

Hi buddy,

The vehicle wont even start - or run enough to test this theory.

I'll try the fuel line thing shortly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...