Jump to content
SAU Community

Recommended Posts

these rims are in great condition. gutter rash on just 1 or 2 of the rims, very minimal.

has roadworthy tread.

the rims are 17x9 3 piece wrapped in 255s

let me know what you have. looking for 17s or 18s. no smaller then 9inches wide. would love 10.5 wide.

will consider bee r rims, te's, driftteks and meisters. let me know what use all have.

otherwise im chasing the $2000 dollar mark for these rims.

test fits are welcome

call or sms stefan on 0413 440 621

26107_116085861738241_100000104843842_283929_3705772_n.jpg26818_120213947992099_100000104843842_307699_1091324_n.jpg

Edited by DMIN8R
Link to comment
https://www.sau.com.au/forums/topic/324990-oz-racing-futuras-eoiswaps/
Share on other sites

  • 5 weeks later...

what state r u in buddy

i know a place that makes the outer dish so u can go 10.5 inches wide if u like and still have the thinner ones at home as well.

i think it only cost like 180 a wheel as well

let me know and ill get his details for u

cheers

julz

White Horse Industries (Wheel Spinners)

http://www.whitehorseindustries.com.au/met...pun-wheels.html

Based in Vic

Tho im sure you can send just one outer Lip in amd ask them to make four exactly the same to what ever dimension you heart desires:)

Im going through another chap in NSW bit more pricey but local to me...

DependinG on what you want to spend you can get inners amd outers made up for some truly custom/big dish...

Edited by krayzie32
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...