Jump to content
SAU Community

Recommended Posts

Ok guys I know this is probably a stupid question, but forgive me for my ignorance. Does the r32 gtst have a hole in the left inner guard, underneath the battery? I'm pretty sure that it was made for the fmic. Qld transport giving me a hard time saying that "I need to restore it to original manufacturer standards". Which makes no sense to me.

Any thought thoughts? previous experience with this

Link to comment
https://www.sau.com.au/forums/topic/327049-stupid-question/
Share on other sites

I would start by moving your battery to the right hand side like everyone elses.

And no there is not supposed to be a hole there.....and no the guy at QLD transport doesn't know what the f**k he is talking about because it has nothing to do with structural strength and does not effect the roadworthiness of the vehicle. Tell him to re-educate himself

Link to comment
https://www.sau.com.au/forums/topic/327049-stupid-question/#findComment-5322582
Share on other sites

back in the day i thought all aftermarket fmic setups where illegal.

now im seeing alot of mechanics pass rwc in vic legit , providing its not structural or important part of vehicle from safety aspect

heading to brisbane in 1 week ... any1 have pointers ? dodgey rwc :P hook me up!

do i only need rwc ? or present the vehicle also?

r32gtr huge exhaust =/

Link to comment
https://www.sau.com.au/forums/topic/327049-stupid-question/#findComment-5323520
Share on other sites

Sorry I meant right hand side...lol If you stand in front of the car it becomes the left side....hahaha

That's what I thought Dan

My sister had to see Qld Transport to get a number of "defects" approved after an officer pulled her over in her R32Gtst. The front mount intercooler pipe came into the engine bay in the same spot as the GTR. As an engineer I simply prepared a letter for her essentially stating what has already been said. It will have neglible structural impact on the car. The fact that the GTRs have a hole in this location and on the passenger side there are more penetrations for the intercooler piping says it all really.

When I had my RB30DET mod plate prepared, the approving facility included the front mount intercooler installation as part of the description for the modifications.

Edited by BH_SLO32
Link to comment
https://www.sau.com.au/forums/topic/327049-stupid-question/#findComment-5323619
Share on other sites

they will say it has to be engineered (mod plated)

o.p. take your car to an engineer and get the hole mod plated

there is no code for a hole in a non-structural area. The only thing you can do is put it under 'Chassis Mod' but it's not the correct code for it.

And yes, before you ask...I have the code of practice here

Link to comment
https://www.sau.com.au/forums/topic/327049-stupid-question/#findComment-5332798
Share on other sites

Can anyone recommend an engineer, around GC or brissy that's not going to charge me a arm and a leg for their signature.

I need the hole certified once I get it reinforced.

Andrew - 0402293256 and tell him Daniel from Elite Racing sent you as he normally doesn't deal with public

Link to comment
https://www.sau.com.au/forums/topic/327049-stupid-question/#findComment-5341877
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...