Jump to content
SAU Community

Recommended Posts

Hi all, havin problems with my aerial since I went to put my tv in car, that wouldn't work, so I put the other cd player back in and now the aerial won't go up and down even though it's hooked, and the clock is dull like it's going flat. Any help would be great.

Link to comment
https://www.sau.com.au/forums/topic/328042-r33-aerial-and-clock/
Share on other sites

sounds like u have blown a fuse. dont worry its easy to fix. u know the fuse compartment on the drivers side in the car? look in there and i think its a acc fuse i could be wrong just check them all and replace. i had similar thing happen to me so i checked each fuse (stupid Japanese righting :laugh: )

the reason. because u were drawing over the 20A that the fuse is made to brake at when u put the TV in the car

Well i tried all the fuses, none blown, not sure what else, clock doesnt have any power now, dead. i will pull off the surround again and look to make sure everything is right behind there, but im 100% sure it is. Any other clues.

i dont know what else it could be... maybe a angry wire that is earthing out? but then the fuse would have blown.

hmmm maybe get the audio wire diagram for your car and for ur head unit and check that everything is were it should be

low voltage on the line for the power antenna or bad ground on antenna and or radio.

clock dim ??? lcd or fluro type clock lights?

I would guess low voltage on that circuit, if the fuse was blown it wouldnt work at all

clock LED only needs a few volts, power antenna needs 12v

Well after searching this site, there has been alot of people with the issue over the years asking about it, but i have not read how they fixed it, did they simply give up and rewire the clock, and in my case my aerial wont go up and down. I have checked everything that i can think of or see and its got me stuffed. Usually im actually quite good at finding issues like this, but not this one. Oh well keep searching for a answer. Thanks to anyone who knows how to solve it.

check the voltage output to the antenna? 12v ?

clock can fail, old nissan clocks did all the time ?

got a photo of it to see ?

antenna ,does it even make motor noise when the radio comes on? if so it's got a broken plastic winder thing inside and most can be fixed

some aftermarket/oem ones use a relay to boost current to put the antenna up? have you investigated that?

I did look around at relay but couldn't see one that it would come under, going to pull aerial connections of this afternoon as I finish at 1 on Fridays so I will actually have some daylight. If I can figure it out, I will just rewire the aerial with it's own online fuse, same with clock if I have too. It's just odd cause the constant power wire for the head deck is only pushin just over 2v all the time, I have to run my own just to get it to work. But thanks to everyone that's tried to help so far.

Well everything is working again, I lost my indicators last night, checked all the fuses and nothing blown, but they still flashed with the alarm, so I checked fuses avian and found one dead, put that back in and clock and aerial started working, but still no indicators, then I fiddled putting the fuse in all the way it can and just tested once more and there they were. I must have a loose connection behind the fuse box, cause I triple checked all the fuses the other day and none were blown. The whole fuse box inside the panel moves so it would not suprise me. So sorry I don't have a solution for anyone else who has this problem, all I can say is check third fuse up from the bottom, left side in side the car, that's the one that ended up shitting itself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...