Jump to content
SAU Community

Recommended Posts

Hey ,

Got my car from Japan today - Driving it home, realised that the rear suspension squeaks to buggery !! It's really annoying as it only happens when you are going really slowly with little to no engine noise. Its like the rear shocks go down like 1-2mm and it make this god awful noise.

The car has after market coils and shocks - don't know what brand yet as I haven't had time to pull the back wheels off. All four corners are damn stiff though.

Put it this way, you open the boot and push down on the rear and you can hear this noise squeak thu the chassis.

It sounds like the shocks need a bit of an oil - But I thought this was all internal ??

The car handles well and can take a fairly decent pothole without jarring too much.

Can anyone gimme some advice on what to look for or what to do with this problem ??

Many Thanks,

Link to comment
https://www.sau.com.au/forums/topic/3281-sqeaky-rear-suspension/
Share on other sites

Ripped wheels off tonight -

The shocks are Tanabe? (never heard of them??) - Looks like the rubber boot that is meant to go over the main shaft of the shock has perished. Don't know if the shocks are any good or not - So I WD40'd the lot - The noise is better, but still there.

I might take it down to Pedders or another suspension shop = see what they reckon.

Recomendations for suspension shops in Sydney ???

Cheers/

yeah i was goin to say that but i didnt know how to explain it the springs sometimes squels where it sits in the shoe of the shock usually cause aftermarket stuff is metal on metal wheras factory have a little rubber boot on the ends of the springs id say a generous amount of electrical tape would do the same thing wrapped around the end of the spring crap job though pulling all the springs out for squeekes!!:D

tanabe usually supply things to nissan like radiators and hoses n ***** are they anything special like hieght adjust. or shocker adjustable if not i didnt know they made shocks!!! Just be carefull with places like pedders cause they try n tell you all this stuff that there "diagnostic machine told them" about you need this that and the other replacing so they can make some money off you

No, not adjustable or anything (Damn Hard though) - The shock part of it is Orange and I they are called Viper Street somethings - Looks like you can undo the top of the strut tower and remove the shock cartridge (As you can tell I have no idea what all this stuff is called) Anyway , it didn't look to difficult to get at so I might pull them apart, clean everything , make sure all the rubbers are OK, test the shocks. Dunno what to do if the shocks need replacing as there would be no Tanabe spares in Aust hey ? Maybe someone else make a shock that is the same ??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...