Jump to content
SAU Community

Recommended Posts

Could some one please comfirm if their HKS 2530 turbos have the numbers 094 0n it.

When i bought the car, the owner said that they are the HKS T28s.

I spoke to the importer (he's friend of mine), he was telling me that he thought that they were the 2530s.

I would really appreciate if the people who own the HKS 2530 could check to see if their turbos had the 094 number on them.

Thanks in advance

Bill

Link to comment
https://www.sau.com.au/forums/topic/32883-hks-turbos-2530/
Share on other sites

mine has a little metal plate that when viewed from the side is between the two housings. it should have Garrett written in the compressor housing and HKS on the exhaust housing. its the bit in the middle of this photo that you can't read because of the reflection.

Link to comment
https://www.sau.com.au/forums/topic/32883-hks-turbos-2530/#findComment-659988
Share on other sites

I can only see the one with HKS & thats where the number 094 is written on.

I've had all the top piping off to change the o2 sensors a little while ago & i still could'nt see the plates, unless they are underneath, there's no way i could see the plate from underneath.

Link to comment
https://www.sau.com.au/forums/topic/32883-hks-turbos-2530/#findComment-660004
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...