Jump to content
SAU Community

Recommended Posts

Hey,

I just found out that Ive blown a head gasket :(

The block has been o-ringed and used a copper gasket.

I was wondering if I could simply remove the old gasket and use a cometic mls head gasket and still keep the o-rings there? Or would I have to get the block shaved to remove the recess for the o-rings and use a thicker head gasket or what?

I was told the pistons were 20thou oversize. If I used a head gasket for 40thou oversize pistons am I able to continue to use the o-rings or is that just silly?

I really dont want to buy anything that isnt going to work.

Thanks,

Lukas

Link to comment
https://www.sau.com.au/forums/topic/329063-head-gasket-issues/
Share on other sites

90% of the time it wil be fine, you just need to check the diameter of the o-ring vs the recess in the head gasket to ensure they dont overlap each other.

I guess I will pull the head off and measure the o-rings to check the size of it. I guess I just get a head gasket which has a bore that matches the outer diameter of the o-ring?

Sorry to sound so dumb, I just want to put any basic question out there

Tried bleeding the coolant for about half an air. Still getting bubbles into that coolant after that long.

Pulled off the cam covers and retorqued/checked the torque on all the head bolts and still getting bubbles in the coolant.

Looks like it is definitely in the bum.

You did goop up around the water and oil holes? Or perhaps used some hylomar?

If you are using a MLS with the O rings, you need to use copper O rings, stainless wont work. In that setup, either the gasket or O rings need to give when crushed, stainless rings with MLS head gasket, neither will give. Also do the ends of the rings actually butt up to eachother nicely? Do you know what the protrusion height is from the deck?

Ill put this up just incase.

post-12828-1279830733_thumb.png

Edited by r33_racer

If you are sure the gasket is leaking you should pull the head off and make any determinations based on what you find .

Its pointless guessing what has happened when you can't see anything .

People I know are not big fans of Cometic head gaskets and for normal use they often use a genuine gasket or if the manufacturer has a competition gasket gasket available one of those .

Always remember that an inline six the block and head are long so the surfaces must be flat and square or things will leak . If the engines doing super duty studs and nuts are always the best fastening option .

From what I hear RB engines don't have HG issues std but if you screw a lot of boost into them then its the same as any half decent OE engine . I believe the wire rings work because they sit in a groove in either the had or the block and attempt to form a mechanical lock just outside the headgaskets fire rings to help prevent them moving and breaking their seal .

I know many won't agree but I think copper gaskets were a means of having a cheap reusable item which could better stand up to high cylinder pressures than the cereal box gaskets cars had back in the 1970's .

Their problem as I see it is that its asking a lot for a non ferrous material that sees uneven heating to remain a uniform thickness after lots of heating cycles and being annealed to go again .

Also its not at all uncommon to see them leak water or oil via small machining marks on the head or block .

Your call , for road I think an OE gasket with stainless rings are fine if done properly . The next stage is to cut the fire rings from a good new conventional gasket , machine same depth steps in the tops of the bores and use parallel wall rings to physically lock the block to the heads deck face . The conventional gasket minus fire rings seals water and oil like they are designed to . The crush seal is critical and the compressed thickness of the rings and gasket has to be carefully worked out . I think Alex at Plazmaman was the first person I'd seen do this on his 700+ Hp FJ20's . Thats three and a half times the factory FJ20 output BTW .

Your call .

I have a spare gasket left over from my build. Cometic 88mm 1.3. will do you trade price if you need it. new in box

Matt

After speaking with Paul from Red R Racing about the gasket issues i was told that you can NOT use a cometic or nitto gasket if it is O-ringed. I have chosen to use an ACL copper gasket and see how that goes.

PM me the price of that cometic one however :D

If you are sure the gasket is leaking you should pull the head off and make any determinations based on what you find .

Its pointless guessing what has happened when you can't see anything .

People I know are not big fans of Cometic head gaskets and for normal use they often use a genuine gasket or if the manufacturer has a competition gasket gasket available one of those .

Always remember that an inline six the block and head are long so the surfaces must be flat and square or things will leak . If the engines doing super duty studs and nuts are always the best fastening option .

From what I hear RB engines don't have HG issues std but if you screw a lot of boost into them then its the same as any half decent OE engine . I believe the wire rings work because they sit in a groove in either the had or the block and attempt to form a mechanical lock just outside the headgaskets fire rings to help prevent them moving and breaking their seal .

I know many won't agree but I think copper gaskets were a means of having a cheap reusable item which could better stand up to high cylinder pressures than the cereal box gaskets cars had back in the 1970's .

Their problem as I see it is that its asking a lot for a non ferrous material that sees uneven heating to remain a uniform thickness after lots of heating cycles and being annealed to go again .

Also its not at all uncommon to see them leak water or oil via small machining marks on the head or block .

Your call , for road I think an OE gasket with stainless rings are fine if done properly . The next stage is to cut the fire rings from a good new conventional gasket , machine same depth steps in the tops of the bores and use parallel wall rings to physically lock the block to the heads deck face . The conventional gasket minus fire rings seals water and oil like they are designed to . The crush seal is critical and the compressed thickness of the rings and gasket has to be carefully worked out . I think Alex at Plazmaman was the first person I'd seen do this on his 700+ Hp FJ20's . Thats three and a half times the factory FJ20 output BTW .

Your call .

Holy shit disco you've done it again!

I will have a look into answering this in more depth as Im tired at the moment. The head is off and the gasket was leaking on the block side of cylinder number 5.

I didnt think I could use a std gasket when it has been bored 20thou?

Sorry for the dumb shitness :) Been up for too many hours

Thanks heaps for the in depth info :(

You did goop up around the water and oil holes? Or perhaps used some hylomar?

If you are using a MLS with the O rings, you need to use copper O rings, stainless wont work. In that setup, either the gasket or O rings need to give when crushed, stainless rings with MLS head gasket, neither will give. Also do the ends of the rings actually butt up to eachother nicely? Do you know what the protrusion height is from the deck?

Ill put this up just incase.

post-12828-1279830733_thumb.png

No the ends of the rings dont butt exactly to be honest. There is a slight gap in between the ends.

And no I don't know what the protrusion height is from the deck :)

Yeh it had enough good, but It was leaking so I can't confirm it was done right. I am going to be using hylomar when I put this next copper gasket on. If this doesn't seal it I think it is going to be time for ANOTHER rebuild!

OK I picked up my new ACL copper gasket yesterday and I am slightly nervous.

The bore of the gasket is 88.25mm and the o-rings in the block are set at 91.5mm (roughly).

The gasket is also 1mm thick.

NOW THE QUESTION

Do you think I will have any issues with the o-ring biting into the gasket nicely or will the o-ring try to fold a lip around/along the bore of the gasket due to the minimal difference/distance between the o-ring and bore?

OK I picked up my new ACL copper gasket yesterday and I am slightly nervous.

The bore of the gasket is 88.25mm and the o-rings in the block are set at 91.5mm (roughly).

The gasket is also 1mm thick.

NOW THE QUESTION

Do you think I will have any issues with the o-ring biting into the gasket nicely or will the o-ring try to fold a lip around/along the bore of the gasket due to the minimal difference/distance between the o-ring and bore?

NOTE the o-ring is about 1mm thick.

90.5mm is the inner diameter of the o-ring and 91.5 is the outer diameter.

New gasket went on today and it looks like we have a winner!!!

I think I might need to get a higher temp thermostat though.

I was sitting around 70 degrees.

Max temp reached was 76 degrees.

Ambient temp was 20 degrees.

ANOTHER QUESTION!

If I had a CR of 7.9:1 with a 1.2mm gasket, what CR do you think a 1.0mm gasket will give me?

I am thinking about 8:1?

Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...